2.5" to 3.5" SATA Hard Drive Mounting Bracket Kit - Dual SATA SSDs/HDDs Mounting Bracket for Mounting Bay , TAA (BRACKET25X2)

This bracket is plastic, but strong enough to do its job. The material is flexible, not brittle, and can be trimmed if necessary - the front panel audio header I installed with this bracket was a fraction of an inch too wide to fit, but it was easy to enlarge the opening and get a perfect fit. All of the mounting holes lined up perfectly with the header and the case, making installation quick and easy. Note that the included fasteners are self-tapping screws and are for attaching the bracket to the case, not for mounting your drive (or other device) in the bracket. Since the self-tapping screws cut threads into the plastic material as they are tightened, take care not to strip the holes by over tightening.

I purchased a new ATX case that apparently doesn't come with 3.5" external bays. I have a black 3.5" USB port/card reader, and I wanted to continue using it with my new case. So, I got this adapter. It is made from fairly cheap plastic (probably ABS or something similar), and the screws that are included are self-tappers for the plastic mounting holes. Since they are self-tappers, you should avoid moving this thing around in the future. Try to choose its permanent home, then install it and leave it alone. You *can* remove the screws, move the adapter, and then screw them back in, but you need to use a trick for re-screwing self-tappers or you will destroy the threads on the adapter, making it impossible to tighten the screws. The trick is is follows: When you wish to screw the screws back in, put them in the screwholes and slowly screw "backwards" (as though you are unscrewing them) while pushing the screw gently into the hole. You will eventually feel the screw sort of "drop" into place. This is because the threads have now lined up, and you can carefully screw it in. Anyway, the adapter is attractive enough, lines up well with the front of the case, etc. Aesthetically it is good. It's just a bit flimsy.

Great product, works well and fits well, but there are two flaws that keep it from being perfect. First, since it's plastic, it could use a ground strap for 3.5" devices that rely on the outer case grounding for ESD protection. I made one by hand, but having to so this was annoying and is unnecessary for metal brackets. Second, it only includes self-tapping screws for mounting the bay itself, which would normally be fine since devices themselves usually come with their own mounting screws. However, the inner plastic brackets you mount the 3.5" device to are over 2mm thick, and most 3.5" devices come with fairly short mounting screws since PC cases have thin metal drive cages. I had to seriously hunt through my collection of old screws to find any long enough.

PROS: * Affordable and well built * Plastic construction seems to be durable, yet flexible * Thick enough that it shouldn't easily break, but my all my screws I had fit ok. * Had all the holes where I needed them which is always a plus * Comes with four mounting screws to mount the adapter to your case. (You provide the screws needed to mount your drive or other device to the adapter. These mounting screws typically come with your drive, front panel hub, card reader or whatever else you're installing) * 2 Year Warranty * The black color matches my Anker USB 3.0 hub and case perfectly. CONS: There really isn't much I'm displeased with, but here are a few things worth mentioning. - There is a slight gap around the Anker USB hub I installed in this. Not major, but if you're expecting a very tight "force it in" fit you might not get it with all devices. I'm worried it might let some dust in but time will tell. - I've read some people have issues with the plastic being too thick for their drive mounting screws. I mention it here but had no issues myself. If there is any issues I suppose you could always get longer screws, remove any washers, or countersink holes slightly if you need to make short screws work. - This is plastic so if you force things I'm sure it will break. - The mounting screws to mount the drive adapter to the case are those sort of "self-tapping" screws or sheet metal screws that chew into the plastic to make their own threads and secure the plastic. In my experience these work fine a few times, but the plastic typically won't hold up if you constantly remove and reinstall them. If you're one of those people that constantly changes things around and builds new computers from existing parts it's something to be aware of. I'm sure you'd have to remove and reinstall this adapter many many times before you chewed the plastic up so much the screws wouldn't hold. Product Dimensions: 8Height 1.1 in [28.6 mm] Length 5.7 in [146 mm] Width 5.3 in [133.4 mm] . . MY EXPERIENCE: I purchased this to install a USB 3.0 front panel hub to add USB 3.0 ports to the front of a computer. It worked nearly perfectly for this use. The USB 3.0 front panel was being installed in an unused 5.25" optical drive expansion bay on a retail HP computer. I needed a 3.5" to 5.25" drive adapter that looked great but had a low profile face and didn't stick out very far. This was necessary to allow the USB ports to be tucked back behind a drive bay door cover to maintain a stock appearance while still providing access to the ports. This mounting adapter fit fine in the stock OEM case's 5.25" drive bay and mounted without issues. The adapter comes with 4 screws to mount it to your case's drive bay. Since this was a stock OEM HP case you can't easily remove one side and so I could only use two of the mounting screws but that's all that is necessary to keep things from sliding around. The ANKER USB 3.0 front panel hub fit with some room to spare. The USB front panel hub doesn't completely fill the hole for the 3.5 inch drive so there is a slight gap around the hub sides and top between the USB hub and the adapter. It's not a huge gap, it looks somewhere between 1/32" to 1/16", but it's enough to notice light and see through when out of the case. When everything is installed in the case I don't really notice the cap at all. This doesn't bother me. Since this is a "one size fits most/all" adapter you can't expect a light tight perfect fit. I could have evened up the gap between the bottom and top by using some washers as spacers on the bottom mounting points. I also could have used some sort of black trim on the inside to really seal this off but I didn't take the time. I'm a little worried about how much dust the gap would let in but this install hides behind an HP optical drive bay expansion bay door cover. The gap doesn't bother me much but I thought I'd mention it. I'd much rather have a little extra room and NOT need to get out files, grinders or sandpaper to make things fit so I won't complain. I didn't have any issues with mounting things up. Screws were just long enough to safely secure everything. It doesn't take much. We're not bolting down jet engines here ;) I'm uploading plenty of images but there really isn't much more to say. Based on the price, fit and final appearance I can definitely recommend this adapter.

I needed this to refit drives into a retro case. Arrived quickly, worked perfectly, and had easy installation. Great price for value

Not a perfect piece of gear but it will work for a GRAUGEAR 3.5 Inch USB C hub and card reader. This is the only thing available. The rack is made from plastic, and you will have to scrap one side with a very sharp craft knife in order to make the Graugear hub fit. In addition the sides of the usb hub don't fit perfectly in the rack, since there is a 2mm gap between the sides where you screw in the hub. You have to insert thick stock card board or even plastic so the whole thing won't be too loose. I have included photos to give you a sense of the difficulty involved. Overall 3.5 stars.

I received them a lot earlier than i was expecting.Despite being very light plastic they are very sturdy.

Sencillo pero cumple su función. Fácil de instalar.

Schnelle Lieferung wie versprochen, original verpackte Teile und bestens einzubauen. Vielen Dank

Excelente bracket para instalar 2 discos SDD de 2.5pulg. en una bahia de 3.5pulg. para discos HDD. Viene con todos los tornillos que requieren y con el cable de derivación de alimentación sata en Y, que es muy util cuando la tarjeta madre no tiene mas puertos molex o sata de poder, y quieres conectar más disco duros o clonar tu HDD.

I wanted USB 3.0 sockets on the front of my PC, so I could plug in external hard disks for fast data transfer. The sockets that were available: the Anker® Uspeed USB 3.0 3.5 inch Front Panel with 2 USB 3.0 Ports Hub fitted a 3.5 inch bay, so this bracket did the job. It is plastic, but seems very strong. The screws supplied were rather short, but I was able to fit it fairly easily.

السلعة ممتازة والحالة جديدة بغلاف الشركة المصنعة والتسليم كان في موعده والمعاملة حسنة من العامل