FRIGIDAIRE EFIC452-SS 40 Lbs Extra Large Clear Maker, Stainless Steel, Makes Square Ice

Review is for the Frigidaire EFIC452-SSRED XL Maker, Makes 40 Lbs. of Clear Square Ice Cubes A Day So I just received this today....we have been using a Frigidaire brand "bullet" style ice maker and it just can't keep up with our ice consumption, this....despite a fridge/freezer with two ice makers....go figure. Got this, Red one....rinsed it out, cleaned everything, and filled all the way with water. I figured, since I had to wait at least one hour for the oil in the compressor to settle, I would give it a good cleaning, and run water through it. Put the end over the sink, removed the drain plug and ... NOTHING. No water is draining. NOTHING AT ALL, despite the reservoir being completely full of water. Must be clogged, or the tube from the reservoir must be blocked or pinched. Checked the manual. Nothing to do except take out the drain plug. (there is a screw on cap, then a silicone "plug"...yep I removed it) So, what to do. I figured it must be a twisted or blocked tube, SO I TOOK THE WHOLE BACK METAL COVER OFF, so I could take a look at the tubes and see if there was a block. Its not hard to take off the metal cover....10 screws and then shimmy it off. Be careful. The metal is thin and sharp. Looked around....NO water in any of the tubes, despite it being full. Checked the drain "filter" in the reservoir and took it out, just in case. Nope, no water coming out. Checked all the tubes. Not blocked. GUESS WHAT IT WAS?? I plugged in the ice maker, just in case....NOTHING is said in the manual. The pump started working right away, and VOILA! water started running out the back drain, which was still open. Apparently to fully drain this, you must have it plugged in...(I didn't turn it on, just plugged it in) I believe the pump will close the lines so it can't drain, once it is shut off. NOTHING IN THE MANUAL TELLS YOU THIS!!..So if this happens to you, don't return it because it won't drain. Just plug it in, and it will start draining after the plug is taken out. Hope this little trick helps you. Now onto the ICE. First batch set on +4 took like over 20 minutes, and it makes pretty thick ice at this setting. Changed it to 0 and it took about 15 minutes. We use chilled, filtered water in our fridge, since using cold water makes ice faster, so the machine doesn't need to chill it down as much. The way this ice machine works is the water from the reservoir is constantly dripped over the square metal grid, which is chilled by the ice maker. This means that the all the water in the machine is constantly "cycled" over this grid, bringing the temp down on all the water. Might as well start with chilled water to help the process. Even on a setting of 0 the ice coming out of this machine is thick and clear for the most part. Love it so far. Its not "loud" but its constant "on" like a mini fridge, until it cycles when the ice is ready. Because of the thickness of the sheet of ice that dumps out, its quite loud when it dumps. I love that it dumps in a sheet. This makes it super easy to bag it up in sheets for storage to use later. This ice is SOLID, and since its clear, it doesn't have hardly any air in it, unlike the bullet style ice makers. This thing is going to get a lot of use, so will see how long it lasts. The price is about double what you would pay for the bullet ones, but so far I think its worth it. Time will tell. *Update* 10/6/22 - well...its been a few days of almost constant use. The ice that this makes is almost clear....for the most part it is, and its SOLID ice, not full of air and cloudy. The bullet style ice makers, make ice with a lot of air in the ice, so that ice doesn't last too long, melts fast. This ice makers ice lasts a good long time, probably double the amount of time for the same "amount" of ice than the bullet ones. The only down sides I can see with this ice maker is...1. that loud noise when the ice "drops" out of the grids. Its pretty loud when it lands in the "bucket" when there is little to no ice in there. Once you get a couple of drops of ice in there, then its almost silent when it drops. 2. You could view this as a negative and or positive. The ice drops most times in a sheet, that you then need to break up. I don't mind this....makes for easy storage. To break it up, we put it in a zip lock bag and then just bash it. It breaks right away, and I don't mind doing this extra step, since the ice lasts so long, and you can get long strands of ice too that fit nicely in your flask or large cup etc. This machine is a little larger than the bullet type, so keep that in mind. I tried +4, 0 and -4 for ice settings, and didn't notice any difference in the ice made, so now just leave it on a default setting of 0. Plug it in, fill with chilled water, and hit the power button and thats it. You don't need to use chilled water, and often times I will put some ice in the water, just to keep it colder in the beginning, to speed up the first batch, which seems to take the longest. Recommended. We have lots of ice now, and with this running, can stock up. *UPDATE* - Love this ice maker. First batch takes a while to chill down the water, but the amount of solid ice you get out of this is a big WIN. Solid ice "cube sheets", but very easy to break up.The ice lasts a good long time in drinks, since the ice doesn't contain much air, since its clear. Just get this. I don't think you will be disappointed!! I still get startled when the ice drops....LOL! *UPDATE 12/12/22* Have had this a while now, and use this almost daily. This ice maker is a WIN! The ice lasts a good long time, and even if you let it run until the bin is full, not that much ice melts in the bin. We do this and then bag it, check the water - add whats needed and continue on making ice. Couple of TIPS- While the ice maker cycles all the water in the machine from the top reservoir where you add fresh water, drips over the grid, then drops into the bottom holding bin to be sucked up and cycled over the grid again, this ice maker will not pull water and empty the bottom holding bin. If you forget to empty the ice from the bottom, and all that ice melts into the bottom holding bin, I have found that it will stay full of water. So don't panic, just start scooping the water from the bottom bin, into the top bin manually to lower the level to under the Ice bin, then continue to make ice. Haven't had any issues with this ice maker yet. *time for another update* 10/26/24...wow its been over 2 years of use and still going strong. This machine makes a lot of ice, and we use it almost daily. I have been using filtered water always, but still clean it about every 6 months, if I notice the water leaving residue. Cleans up very easily with this product: https://www.amazon.com/gp/product/B0BCJQ5SZX/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1 This stuff is a win! Easy to use, I dump it in and let it sit a while, then just run the machine like normal, letting the water solution circulate and make ice. I make ice for a couple batches, and keep running water through the machine...once the ice becomes clear again, then I fill up the reservoir and empty from the drain plug. I do this a couple of times, then all done. Of course this type of ice maker is loud when the ice drops, but other than that, it has lasted very well for us in almost constant operation.

10/2025- UPDATED 5 year review!! (Probably the last unless it hits 10 years) Bumping to five stars as well due to longevity. Updated review of the update. I may have messed up my latest update so I guess I have to start over. Here we go. I’m one month shy of FIVE years, but due to the recent dramatic drop in price, I felt inclined to chime in. My experience is probably not the norm, considering all the horror stories I hear. But here we are. I recently experienced a scare after cleaning the unit and it acting strange. Left it unplugged for a couple of hours and it went right back to making ice! If I had to do it all again, only bottled water. My filtered tap doesn’t cut it. Cleaning is still a pain. Bought a cleaning kit and the brush pulled out some horrific stuff. Seriously, clean this thing like it’s a full time job! This thing just keeps on making the ice! I think that whatever machine you get, buy the insurance. Remember, my first machine leaked, and this one appeared used. Good, or bad, this ice maker has brought me more joy than just about anything else I own. Well, that’s all folks. Stay frosty! UPDATED 2 1/2 year review (7-23) I've now had my unit for just over 2 1/2 years and still going strong. It's used pretty much every day with a rare day off. One of the things I wanted to correct from my earlier review (that i realized shortly after and had a 'duh' moment) is that I was wanting a way to only make X amount of ice. I had been just adding X amount of water to achieve that and right after leaving the review realized I just kept over looking that timer button. DOH! Now, on to an update: It's still a pain to clean. I occasionally think that the bullet style makers would be better as the Ice sheets need to be broken up if using smaller glasses or cups. The thicker you make the ice the harder it is to break up, especially while still in the machine. Took awhile to figure out, but it seems the coating on the metal part that forms the cubes is flaking off and has to be cleaned out. Occasionally it needs to be unplugged to 'reset' as it will not respond every so often after clearing ice when it shows full. You also need to have it plugged in to fully drain all water in the reservoir. But these things are trivial, I only mention them so others have a full understanding and can compare accordingly. Overall, I still enjoy this machine very much. The minor annoyances are nothing compared to having fresh cold ice relatively quickly. I especially consider myself lucky when I see so many others have their units fail frequently, which is something that would make me consider a much cheaper unit. Also, consider getting a larger scoop that the one that comes with it. Also, remember the scoop is almost useless when the ice is still in thick sheet form, so maybe consider getting a pair of tongs to go with it. ------------------ I have now had this for 7 months and found a more than a few pros and cons. I'll get the company, and not the machine, related stuff out of the way right now. First unit I was sent leaked water from some spot and at first I wasn't sure if this was condensation or what. I returned the first unit because whether or not that was a defect I wasn't going to use a machine that leaked all over the counter no matter what. Second machine arrived and NO leaking at all. So the first unit was in fact defective. However, second unit was obviously a USED machine! I kept the second machine (maybe a poor choice) because it at least did not leak, and the 'used' factor was only noticeable really due to the water spots and a bit of grime in the reservoir. Nothing major, just a good cleaning before any real use, was required. Let's start with the pros: Clear ice (keep that machine clean though) Sheets of ice that last (melting is slow) Adjustable time to make thicker sheets (cubes) I run this a few hours every day. 7 months, every, single, day. Cons: Most noticeable is the cleaning factor. I have smallish hands for a guy and I still can't reach areas well enough to give this thing a deep clean. That's really it for cons I suppose. There are some things I can nit pick if anyone cares. Read on if that's the case. Included scoop is useless. This thing makes 'sheets' of ice that laugh in the face of this minuscule scoop thingy. (not a big deal, but if this kind of thing is important to you, maybe just buy one of those bullet ice machines) Other people seem to know how much ice this can make with X amount of water. I, however do not. So I would love an option to select X amount of sheets (this thing makes sheets of ice remember) to be made. Description says it runs on 120watts. Really? I didn't test this with a Kill-o-Watt yet, but I did try and use it with two different portable battery packs that could not handle the initial load. So this thing must spike well over 300watts (seriously, 120watts ??) and only consumes the stated 120 when it's in the 'hey, about to dump this sheet of ice out' stage, or they simply meant it runs on 120v. I'll need to test this for off grid use. Overall this is a great machine. I'm listening to it in the 'I'm about to dump this sheet of ice out' stage right now as I type. I did encounter a defective initial machine, then the 'here, have a used one' after that, but I am still happy with my purchase. I don't remember the exact reason I chose this over the 'bullet' style machines, but I think it was based on output(?). However, I think I would have been happy either way. Those bullet machines put out individual cubes, which would make the included scoop in this machine actually useful! This machine puts out 'sheets' of ice that you can break up if storing in your freezer or whatever. Personally, I use them in my tumblers. One sheet fits well when broken in half. Solid sheets seem to last longer when used in a cooler for other stuff. I think this all comes down to personal preference but honestly you could simply go with which ever unit was cheaper and be just as happy. Hope this helps someone reach a decision. Once I get my solar set up in place and see how this machine fits in I'll update my review.

My wife was getting hip surgery and was told that she needed to use ice on her hip for at least 3 weeks following her operation. My fridge icemaker was just not going to be able to keep up with the demand, so I started reviewing ice makers. This Fridgidaire icemaker was reviewed well on Amazon, and advertised that it made clear ice. Most importantly, this unit advertised that it could make 40 lbs of clear ice in a day, which is much more than many of the cheaper ice makers. Since I figured it would be nice to use this to make ice in a home bar after she was done with it, I bought this unit. This unit works by dribbling water over a vertical metal grid that looks like an ice cube tray. The metal is cooled and the water freezes as it pours over the grid. The longer you let the water flow, the more completely the ice cube forms within the grid. You can adjust the thickness of the ice within the grid by a setting on the touchscreen. I set mine to maximum to get solid, clear cubes. When the freezing is done, the water stops flowing and the ice cubes are pushed as a "block of cubes" into a bin. The Good: - If you use filtered water, the ice is indeed clear and doesn't have those annoying hollow "holes" in the ice that I associate with cheap ice makers - The product looks great. I really like the red and black coloring, and it looks good, not cheap. - It will make 40 lbs of ice in a day if you are diligent about emptying the ice cube bin frequently. - The ice maker makes about the same amount of noise as a dorm fridge. There is certainly a fairly loud clunk each time a sheet of ice falls into the tray, but the overall ice-,making process was less loud than I expected. The Bad: - The ice cube bin holds maybe 4 or 5 "sheets" of ice before it fills up and the machine stops. Since the bin is not cooled, the ice starts to immediately melt unless it is taken out and placed in a freezer or cooler. - That means about every hour or so, you must go into the machine and remove the ice and put it somewhere cold if you want to max out on the ice production. It would have been much nicer if the holding bin kept the ice cold. The ugly - If you fill the unit with water and let it run overnight, you will wake up to 4 or 5 sheets of mostly melted ice in the tray. - The ice machine works well, but is a bit difficult to drain completely during cleaning. I worry that you could easily leave some water behind which might lead to mold. Overall Grade: I give this a B+ overall, I used the heck out of this thing for almost two months. I bought some ice machine descaler and cleaner, and cleaned it once during my ice-making marathon. Cleaning and descaling was a breeze. I would have given this a perfect A+ if the ice holding tray area could keep the ice from melting.

I had high hopes for this ice maker as a replacement for my freezer’s broken ice maker, but my experience has been far from ideal. Here’s a breakdown of the issues I encountered: 1. **Inconsistent Performance** – It does make ice… when it works. 2. **Excessive Moisture** – The ice comes out very wet. 3. **Constant Monitoring Required** – You either have to wait for ice to accumulate before transferring it to the freezer or move small batches when the bin gets full. At least twice if you fill thw water well. 4. **Freezer Dependency** – Since the ice is so wet, I have to solidify it in the freezer. I use metal containers (hotel pans) specifically for this purpose. 5. **Tedious Once solidified, the ice needs to be broken apart. I use a metal meat tenderizer for the task, but if done immediately after freezing, the chunks stick together and become difficult to separate. 6. **Problematic Ice Cube Settings** – The thick setting is too thick, while the thinner setting produces partial slabs. The "0" setting is somewhat effective, but it still requires hammering each batch. 7. **Lack of Cleaning Functionality** – Surprisingly, there’s no dedicated cleaning function—just instructions to wipe things down, which seems inadequate. 8. **Build Quality Concerns** – On its first use, the button panel started popping up, exposing the unit’s inner components. While I could press it back into place, this doesn’t inspire confidence in its durability. 9. **Deteriorating Performance** – After about ten uses, the machine began making unsettling noises and eventually stopped producing ice altogether. 10. **Inefficiency** – The entire process—from ice formation to freezing, transferring, and breaking—takes far too long. I could easily fill ice trays twenty times over in the time it takes to manage this machine. Ultimately, this ice maker demands too much effort for too little payoff. If reliability, ease of use, and efficiency matter to you, this might not be the best solution.

Works great as long as your willing to keep it clean. Our ice maker in our Samsung fridge is kaput so I bought this after watching YouTube reviews. I make about 10 one gallon zip bags worth of ice at a time, then add about 1/2 cup of vinegar into the water and run it few cycles, drain, and put it away to air out completely. If your willing to make sure you get all the water out of it after each ice making session it will keep running for you. I think most people are lazy and just leave it sitting with water in it then they run into problems. So far I'm very happy with it. Way less moving parts than the cheaper bullet type ice makers. Only the compressor (sealed unit link your fridge) and water pump are the moving parts. By the way, the first basket or two of ice is super clear (which I like), subsequent batches that session are not near as clear, I don't know why this is. Maybe air gets in the ice once it really gets going, ice is fine, just not as clear as the first batch. I don't use filtered water, just from the kitchen tap. Update: Still going strong after 18 months, on two occasions the water pump would not prime upon first startup after sitting since the previous cleaning a few weeks prior and it made a squealing sound, I banged the side a little and it started pumping water. This has only happened two times over dozens of ice making sessions. After 18 months I would still purchase again.

PROS Frigidaire's EFIC452 XL Maker is the perfect way to make large quantities of ice quickly and easily. Its 2.3 liter reservoir can produce up to 40 lbs. of clear squared ice cubes per day, making it ideal for parties or other events where you need a lot of ice. The high-efficiency design means that it can make 24 perfectly squared ice cubes in less than 15 minutes and stores up to 2.4 lbs. at a time. The first batch of ice will take longer because the ice maker refrigerant needs time to cool the water, but after that it will be much faster. The electric ice maker is also designed to be quiet and runs on just 120 watts, making it both energy efficient and unobtrusive. The user-friendly electronic controls make it easy to use, and the modern design with its large through-window lets you watch your ice being made at all times. CONS While 2.4 pounds of ice in one hour may seem like a lot, it can easily be depleted if there is a large demand for ice. The room's ambient temperature is important for the ice maker because it helps regulate how quickly it can produce ice. If the room is too hot, the ice maker will work slower. A consistent ambient temperature in the room will help ensure that the ice maker produces as much ice as possible in a timely manner. As we learned the hard way, running the icemaker on the countertop over a dishwasher is a bad idea because it will heat up the ambient temperature, making it difficult for the ice maker to produce ice. The dishwasher produces a lot of heat, making it more difficult for the icemaker to cool down and produce ice. Even though it can produce up to 40 lbs. of ice cubes per day, the EFIC452-SSRED XL Maker's reservoir only holds 2. 3 liters, so it fills up quickly. This means that you'll have to constantly monitor the ice maker to ensure that there is always a fresh batch of ice cubes being made. If the reservoir is full and there is no more room for ice, the machine will stop producing ice until space becomes available. What we find works for us is we start making ice a few days before a big party and fill up ziplock bags of ice. That way, we have plenty of ice on hand and don't have to worry about running out. Plus, it's really easy to just grab a bag of ice from the freezer when you need it. Overall, we think the Frigidaire EFIC452-SSRED XL Maker is a great ice maker for those who need a lot of ice, but just make sure to plan ahead.

Love this ice machine but our first one accidentally got broken so we ordered the same one. The new one arrived completely BROKEN because it was clearly dropped/damaged during shipping. My issue is, Amazon just put it in a NEW Amazon shipping box and failed to inspect the machine in its original, BROKEN packaging. Ordered a replacement so hopefully they don't make the same silly mistake. This ice machine works well and is generally pretty quiet. It recycles the melted ice water which is a plus. ONLY USE FILTERED WATER or jugs of filtered water. Tap water has way too much minerals and other things in it and will mess up the machine and ice quality. Use a basic "ice machine descaling solution" from here on Amazon to clean it. It should be cleaned about every month or every other month. It's cubed ice so you can't really chew it, but you can stick it in a blender if you want crushed ice. We tried getting a nugget ice machine but NONE of them recycle the melted ice water which sucks in my opinion.

I would give this icemaker a great review however, mine makes some gosh awful noises when it ingests water via the pump, making me anticipate its death soon after only having it for a little over a month. Aside from the lapses of constant groaning this unit makes ice vertically vice horizontally and makes a lot of ice quickly. Otherwise I would give this unit a 5/5 stars for producing a great amount of ice, and producing ice quickly. The square ice lasts pretty well too. It automatically shuts the unit off when ice is full, other than the terribly noisy pump ingestion, this unit is really a step up from the little semi rounded unit that frigidaire makes, which did well until it continually got moldy after multiple cleanings.

Al cambiar de ciclos tiene un ruido extraño que no hacía cuando recién empezamos a utilizar el producto.

Es adecuada, aunque es pequeña, uno quisiera que el espacio para almacenar el hielo fuera más grande, en caso de tener una reunión y necesitar mucho hielo, solo es cuestión de cuidarla y mantener la bandeja vacía y rellenarla periódicamente de agua, para mí fue una excelente inversión

The ice maker holds 2.3 litres in its reservoir, and will shut off automatically once the basket of ice is full OR the water reservoir empties. Empty the ice basket or add water to the reservoir and it will start up again automatically. You'll need to empty the ice about every hour or add water every couple of hours or so. (but you'll quickly end up with more ice than you'll know what to do with!) I only make my ice using bottled or filtered water. The ice will be clearer, taste better, and won't clog up the machine with minerals and deposits. I originally purchased a less expensive 29lb per day Frigidaire Ice maker but took it back after only a few days. Problem for me was the cloudy and very soft ice that it produced. I was hesitant to spend too much more just to get clear ice, but both my wife and I are really glad we spent the extra $$ to get what we really wanted. With commercially produced ice selling for $3.00 and up per bag, it won't take long to pay for itself. Be aware that the ice maker does require regular cleaning (pretty easy to do with the right stuff) so you may want to order some Ice Machine Cleaner and De-scaler that is safer than bleach. (also from Amazon)

I bought this Ice Maker to replace one that made bullet type ice, was an incredible power-hog, and gave up the ghost less than 3 months into having it. While this one does take up a decent chunk of counter space, I'm really happy with how it works; super straightforward operation, nowhere near as loud as the other one I had, relatively quick, and makes enough ice for me in one cycle to only run it every two-three days.

Had this for 4 months so far. It works well and creates lots of clear hard ice cubes. It’s not quiet but not noisy either. The only pain is having to break up the sheets of ice and they all freeze together. I bought a small metal ice scoop which I use to break the ice apart, I’m sure an ice pick will work well too.