POWERTEC Bench Grinder Wheel 6 Inch White 60/100/150 Grit, Aluminum Oxide Grinding Wheel for Bench and Pedestal Grinder, 3/4" Thick 1/2" Arbor, Sharpening & Shaping Drill Bits, Blade, Chisel, 3PK

This worked pretty good to clear on my grinding wheel. The head loosens up while using it, but maybe it was just the way I was holding it. Overall, I am happy with the purchase.

This works great. I was getting ready to buy a new grinder wheel. Instead I used this and in about 2-3 minutes I had a wheel that looked brand new.

I really wasn't expecting much especially at the price but it's not bad. The wheel on the grinder was really badly grooved and while I had a single point dresser I still wasn't having any luck getting it fully flat. This guy? Seconds and it was done. I was really amazed both by the results and the fact that there was no breakout on the dresser. There was some powder it ground off the wheel but aparat from that it still looks good as new. Only having used it once I can't honestly speak to it's durability but this little guy was worth the purchase price for me.

I never dreamed this would work so well. I have it on my Y T Chan Bob Ease Shop

I reluctantly purchased this tool because I really didn't think it would 1) work well and 2) last long. Well, I was wrong on both counts. Have 2 bench grinders, with three stone wheels between them. Working with aluminum on grinders is a mess, because lots of aluminum gets embedded in the wheel and doesn't come off even when hit with steel bar. To add to the aluminum mess, all three wheels (fine, medium and coarse) were worn unevenly. Round corners, groves in centers, etc. This little tool cleaned up and trued up all three wheels in a few minutes. Add to that the tool has enough life left to do all three wheels two or three times again. The trick to using this tool compared to the "pizza cutter" tools, is to not push hard. A nice light touch does the job. The wheel just wears down in a flash. There was stone dust all over the work bench after using this tool. I did push hard at one point using the edge of the tool, and the diamond grit wore off in about a 1/8 inch wide stripe half way down the face of the tool. Pushing hard got me nowhere. Light, easy pressure works best. Now the wheels are square. And 95% of the embedded aluminum is gone. Ground an old screwdriver square and true with the wheels and everything was smooth sailing. No grabbing, no bumping, just smooth grinding action. For half the price of a new wheel, this tool did a great job. Saved me buying new wheels all around. Nice tool. Great bang for the buck.

I'd never dressed my grinding wheels before, and it was time. Bought this and within seconds the wheels were as good as new. For the price, you can't go wrong.

Works good. Cleaned up the face of the grinding wheel really well. Can't tell it took anything off the tool. Should last for years.

Lightweight construction and lots of pieces flew off initially but it still dressed the stone well. Not sure on the longevity but it worked in a pinch

Yes, it's smaller than I expected...about the size of an expensive razor. I didn't think it would work as well as it did, however. Within minutes, it ground down both my grinding wheels to a like-new flatness. Very happy with the results.

A cheap and efficient way of tidying up my small bench grinding wheel. Not sure how long it will last, but for the price it’s done it’s first good job with little signs of wear. Hopefully this will last a good while longer yet.

looks good hope it dresses my grinding wheel

Ahora tengo; unas piedras nuevas, Me encanto Una Maravilla en un minuto solamente

I use my bench grinder to sharpen steel drill bits, in this order my grinding wheels always need to be perfectly straight and fresh, the product design and quuality is very good. easy to handle. it does very well its job, the only problem is there is not a thick layer of abrasive material. I d'ont expect it to last more then two years for me. if someone would use this tool every day on a big grinding wheel it would not last a month. Still great tool for light duty application.