NBS-6040 CNC Router Machine with Custom-Made 710W 7000-30000 RPM Trim Router Spindle & ER-11 Collet, Linear Rails & Ball Screws on 3-axis, Engraving for Wood Acrylic Aluminum

Great little machine. Used Vetrics and added the 7” touch controller. Cut some 170 parts 3/4” “U-Channel” 1/8” aluminum, much more precise then our drill press setup. Setup was a breeze.

I'm new to the CNC market but have been doing woodwork for years. I wanted to get a CNC that could do a good size project. Most entry level machines are typically too small, and the more expensive machines were too big. This one is perfect right in the middle. And within this category you pay a little bit more money for the better construction it comes with. This is very solid and sturdy. And the spindle it comes with is rather nice as well. I wish it came with a 1/4 inch collet however. But those are cheap to get, so no biggy really. I wish the hand control was bigger. And I have some issues with the candle software, so I just use vectric. And I wish it used a USB stick versus the micro SD. But that's just me, maybe there's a reason nymolab went that route. Overall though, this machine is really really nice. Very sexy looking compared to other units. The customer support is top notch as well. Being new to this market I had many questions and they have been with me every step of the way. I did have an issue with the spindle and they replaced it within 2 days to me! I think it's great that a company takes responsibility and acknowledges their customers. The packaging was great and easy to assemble as well.

Instructions for the machine set-up were excellent and everything went together perfectly. I purchased the dust shoe, MPG Handwheel Controller, and 4th axis rotary module which all arrived together with the CNC machine. Recommend a little planning for delivery since the box weighs 130 lbs. As someone new to CNC, I have been struggling to figure this out. Instructions for installing Candle and Easel software came with it, but I have been evaluating a number of other software programs to see what is most beneficial for me, including cost. I highly recommend the dust shoe which works very well, and the MPG has turned out to be a time saver. Customer service has been very good. They have replied to all my questions in a timely manner. I had an issue where the router spindle would stop turning during a carve. Being new at this I had no idea if the issue was software, computer or physical. I emailed Nymolabs with the problem and they sent back a number of things to check. At their troubleshooting suggestion I was able to trace it to the router power cord attached to the x/y arm. After describing this to them they sent me a new cord with instructions on how to install it. Works fine now, and I’m looking forward to hopefully mastering CNC carving someday.

After 4 months and only 7 hrs of carving the spindle has quit working. It trys to spin and does just a little but nothing up to speed. Not sure if it's the spindle itself or the control box. The x,y and z axis still work properly so I'm assuming it a bad spindle.

Super powerful, accurate and well made machine. I bought this as an upgrade to a fox alien masuter pro. It's a massive upgrade. It's easy to put together and everything about it just seems to work. I mainly run programs from my laptop, but having the offline controller is nice. It's an excellent addition to my little workshop.

I’ve had a few of these bench top CNCs and not had much success cutting even the simplest materials. We cut carbon fiber to 4mm and recently wanted to see exactly what this machine could do, cutting grade 5 titanium with very conservative feed rates and plunge rates was no issue, we don’t carve or cut any wood with this machine and it’s strength and precision for the cost is outstanding, simple to assemble, easy to calibrate and we can’t recommend this highly enough, don’t waste your time with cheaper models, spend the money you’ll be glad you did.

I wrote an earlier review sharing how some of the screws had problems stripping and cross-threading. After contacting Nymolabs I was sent replacement support bars. The new support bars had no thread issues and was able to get all screws installed with no problems. Regarding the tracking issue I reported, the connector was not engaged properly. The marking on the connector is not clear and it can easily be connected in the wrong orientation. Once I had it connected properly the machine tracking was synchronized and have had no problems since then. Overall, it is a good machine. I have used it for cutting carbon fiber parts and it has done well.

With a plethora of run-of-a-mill outfits offering so many ho-hum cookie cutter machines, Nymolabs stands head and shoulders above the rest! Being a woodworking retiree with over fifty years experience and not one, but two fully equipped wood shops I have spent considerable amount of time and resources equipping the shop(s). Product value for the money and brand follow up support are what makes a company wallet-friendly for my budget and Nymolabs is second to none. My expectations for the 6040 machine were far exceeded. The design, construction and operation of the machine are on or above par with any of the internationally recognized brand name tools that have found a home in my shop. Even the step-by-step instructions are expertly illustrated and printed and no detail is omitted. As such I have also purchased all the associated accoutrements except for the laser module and look forward to acquiring that as well. Each piece has followed suit and even the packing and packaging have been nothing short of amazing. They have also kept close contact with me while working through one very minor hiccup in fulfillment by Amazon which was expertly resolved. The only reason I give them a 5 is because nothing higher is possible! Thank you (Lily) and the whole Nymolabs team