Question 1

I have a 2 hp 3 ph  220v   motor.  3400 rpm.  60hz.      would the hy    or the gt series vhd be best in this situation?

Accepted Answer

I recommend the GT2.2kw model.GT series adopts vector control, which is very suitable for low speed rotating motor.

Question 2

When i have it set to 60hz max output, is there any way to make the potentiometer match this? it reaches 60hz in the sweep of the knob very quickly

Accepted Answer

Yes. This is because the firmware is reading the voltage off the pot and applying the fraction of that control voltage to the *original* 400 Hz max speed internally, since 60 is only 15% of 400, you will reach 60Hz (and max out and stay there) after only 15% of travel from the pot which applies 15% of the control voltage (usually 10 volts) back into the speed input. The answer is to provide 15% of that voltage at your max pot travel. The way to do this is to add (insert) a fixed resistor in series with the end to end resistance of the pot between the positive end of the pot and the positive control voltage supply. You can do the math on the voltage divider, depending on the value of pot you are using, but the value of the pot should be 15% of the total resistance of both the pot and the fixed resistor’s value added together. It works out to 5.666 times the value of your pot. Say your pot was 1K, add a fixed 5.6K in series, so the total resistance is 6.6K and 1K/6.6K is about 0.15 or 15%. The wiper is still pulling voltage off the bottom 1K, so even at the max “speed” position, instead of giving the full 10 volts, it will only give 1.5 volts because of the voltage divider effect of the fixed resistor. Hope that helps. Yes I am an EE and yes I ran into the same issue. The right answer would be for them to fix the firmware to scale the input to the max speed you have it *set to* rather than the max speed it’s *capable of*, but probably not going to happen any time soon.

I should note that there is a minimum amount of current that must flow into the sense wire off the wiper for the VFD to be able to read/register it. It’s normally a very small amount, but if you were already using a really large value pot (like 100K?? or more) you may have to switch to a smaller pot so that the new total allows enough current to flow, maybe?? 20 milliamps (.02 Amps).  It probably won’t be an issue, so roll with what you have unless it’s a problem. If you’re smart enough to realize you should limit the top speed to 60 instead of 400 and understand *why*, then most of this probably makes sense I hope.

Question 3

Can this be powered with 110v and run a 1.5hp, 3 phase motor?

Accepted Answer

I am using 220v 2hp 3 phase. So far so good. It is advertised 220v so I can't answer about 110v.

Question 4

The max speed it is jus 11350 should t24000

Accepted Answer

you need to set VFD Hertz parameters consistent with your motor.the speed range is 0-24000 rpm if your motor is 400 hz,.

ASIN	B0775BKKNJ
Antenna Location	CNC router, spindle motor, compressor, grinder, mixer, ventilator, slitter, conveyor, elevator, centrifuger, lathe
Battery Capacity	7 amp_hours
Best Sellers Rank	#77,658 in Industrial & Scientific ( See Top 100 in Industrial & Scientific ) #4 in Power Spindle Sanders #63 in Motor Drives
Brand	HY HUANYANG
Built-In Media	red button "stop"
Color	Grey
Customer Reviews	4.1 4.1 out of 5 stars (51)
Electrical Output Waveform	Pure Sine Wave
Frequency	400 hertz
Input Voltage	220 volts
Inverter Capacity Volt-Amp	1500
Item Dimensions L x W x H	6.7"L x 5.1"W x 6.3"H
Item Weight	3.4 pounds
Manufacturer	Huanyang Electrical
Mfr Part Number	HY01D523B
Model Name	HY01D523B
Model Number	HY01D523B
Output Power	1500 KW
Output Voltage	220 volts
Peak Output Power Watts	1500
Power Source	ac
Standby Power Shutoff	High Efficiency
UPC	724509857872
Unit Count	1 Count
Wattage	1.5 KW

VFD Digital Phase Convertor 1.5kW 2HP 220V Single to 3 Phase

Details

Details

Description

Specifications

Common Questions