Geeetech TPU Filament 1.75mm, Shore 95A Flexible 3D Printer Filament with High Elasticity, 1KG (2.2lbs) Spool, Dimensional Accuracy ±0.03mm, Fits Most FDM Printers, Clear Blue

You've saved my EcoReco (Patgear) S5 electric scooter. I print new rear tires to go on the hub motor ever since the original wore out at 300 miles or so. I've got over 1,000 miles on it and this has been the best material yet. My most recent attempt had been PEBA which was expensive. It seemed ultra promising, and gave one really great ride. However the PEBA deforms and stays that way with enough force. This meant that the perfectly tight wheel stretched onto one motor half then clamped by the other side rolled out and got larger around, sort of like rolling dough, until it was loose on the motor. I had ordered this TPU as a backup in-case that happened at less than half the cost. Well, it's the best performing TPU I've used for this so far! In-fact, I have over 100 miles on the printed tire right now and while some sharp rocks split it a little, it has basically no wear at all. It also hasn't stretched or loosened on the wheel. I chose clear orange since I always loved the bright orange wheels on the GoMotorboard 1500x and 2000x transporters I had. I got a clear type, specifically to maximize layer adhesion since there's no chalky pigment powder in the mix. I printed this on my massive delta printer 100% solid at 260c, no fan, no bed heat. I used 160% flow to compensate for the long Bowden tube. If you try this make sure to design a thin brim that prints on both sides into the model if you slicer only adds one on the outside. The TPU will shrink and lift a bit from the bed, so minimize that. The resulting tire is almost air free, nearly solid, and pretty damn indescribable. The spool has a very tangly look, but I had no issues with my 20 hour print despite the wiggly looking filament. It arrived perfectly vacuum packed with a desiccant packet. I did not dry it, yet I heard no crackles or other signs that it was wet despite me printing it at the highest temp my delta could go. The 95A is perfect for scooter wheels. It's not quite audible on the road, but low rolling resistance and fairly thuddy across sidewalk cracks. Perfect really when the focus is rolling efficiency but you don't want to sound (or feel) like a hard skate wheel the whole way. I had no clogs, no feeding issues, and again, it prints like a dream. This TPU had less shrinkage warping my large solid wheel than the Overture I used before too. I will be ordering more! Thanks!

Great color and print. The price is just right for the quality product. We love this filament and have bought other colors with this brand. The Tri color is beautiful for all builds! Makes things like a fidget cone look like we did 2 prints but it is all off this spool. Really a quality product that leaves us with a beautiful build!

Great tpu for the price. I print on a Bambu A1 and it does not have issues running from a dry box through the AMS. I have not tried PLA supports yet, I need to print a adapter for the reels because the inner diameter of the reel is larger than the spool hold on the AMS.

GEEETECH Filament Review Overview In the past, I’ve printed with Geeetech’s metallic pink and metallic blue filaments—both performed excellently and left a great impression. This tri-color silk PLA didn’t disappoint either; it continued that streak with ease. This review covers Geeetech Silk PLA Tri Color Filament (1.75 mm)—a coextruded blend of blue, purple, and black with a metal-like shimmer. I printed all test models on a Creality Ender 3 Pro, using settings that represent what most users might try out of the box, with only basic tuning. All prints were done straight from the spool with no drying. Test Setup • Printer: Creality Ender 3 Pro • Nozzle: 0.4 mm • Slicer: Cura 5.10.1 • Layer Height: 0.20 mm • Infill: 20% • Bridging Enabled: Yes • Bed Surface: Longer textured glass plate • Ambient Conditions: Approx. 24 °C, ~65% RH • Print Time: Approx. 2 hours Print Results Metric Observation Dimensional Accuracy Cube: X 20.15 mm, Y 20.12 mm, Z 19.92 mm. Cylinder: Ø 19.95 mm, Height 19.75 mm. Excellent tolerances for standard calibration pieces. Layer Adhesion Strong; models held up well under light flex and handling with no signs of delamination. Surface Finish Smooth satin sheen with mild reflection. The tri-color effect adds a premium look without overpowering detail. Bridging Clean on all spans of the temperature tower; consistent filament flow, no visible sagging or webbing. Overhangs Performed well on moderate angles—better than typical silk PLA in unsupported areas. Stringing Very minimal, even at 190 °C. A few faint wisps—barely noticeable and not an issue. Warping None observed across all models. Jamming No jams or clogs during the full print session. Odor None noticeable during printing. Pros • Excellent dimensional accuracy • Beautiful, reflective color transitions • Virtually no stringing • Great layer adhesion • Easy to work with right out of the package Cons • Silk finish can obscure fine details under certain lighting • No resealable bag included in packaging Tips & Tricks • Ideal Temp: 215 °C worked best across test models (but may vary by setup) • Bridging: Enable it for best horizontal performance • Retraction: Basic retraction settings were enough—no special tuning needed Images 1. Temperature & Bridging Tower – Shows consistent bridging across all levels 2. Classic Rook – Clean crenellations, strong vertical structure, and smooth layers 3. Calibration Set – XYZ cube, cylinder, and rook for scale and detail comparison Final Verdict 5 / 5 stars. Geeetech’s tri-color Silk PLA exceeded expectations in both aesthetics and performance. It printed cleanly, stayed within spec, and delivered models with just enough shine to stand out without compromising function. It’s a solid pick for anyone looking to add both style and reliability to their prints.

I was a little hesitant about buying this filament at first. After using it, I was impressed with not only the color, but print quality as well. Nice color transition.

I’m a creature of habit, and it’s hard to pull me away from my Sunlu routine. However, Geeetech Dual-Color Silk really impressed me. It provides a level of visual depth that single-color filaments just can't match. If you want to take your decorative prints to the next level, this is a fantastic, reliable choice.

The Geeetech Silk PLA Filament in Red Black Ombré is such a beautiful filament! I love the unique color transition and the shiny silk finish it gives my 3D prints. The ombré effect creates a really eye-catching look and adds a special touch to finished projects. The only reason I’m giving it 4 stars is because it can be a bit finicky to work with. You have to make sure the filament doesn’t get twisted or tangled, as it can cause issues while printing. Once you get it set up properly, though, the results are definitely worth it. Overall, this is a gorgeous filament that produces stunning prints. It just takes a little extra attention during setup and use. I would recommend it to anyone looking to add a unique, colorful finish to their 3D printing projects!

This multicolor silk PLA filament produces some great-looking prints. The bold gradient transition was exactly what I was hoping for when I ordered it. ✅️ What I like: -Full 2.2 lb spool with tight winding. I have not had any issues with loose filament, tangling, or feeding problems. -Striking color blend. The primary colors are red and black, but there are also noticeable gold tones. This really stands out on movable prints like fidget toys, especially when viewed in motion. -Solid and opaque prints. My finished prints have come out strong, without brittleness, fragility, or unwanted translucency. -Clean performance. I have not experienced stringing, oozing, or nozzle clogs while printing. -Good bed adhesion. It adhered well to a clean, smooth PEI plate at 210°C. The listed print temperature range is 190°–230°C. ⚠️ What I didn’t like: -The red is darker than expected. On many prints, it leans more maroon rather than bright red. -The gold tones may not suit everyone. If you are specifically looking for a simple red-to-black gradient, the added gold may be a drawback. Overall, I’ve had a very good experience with this filament. The color contrast is bold, the printing performance has been reliable, and the finished prints look smooth and eye-catching. If you enjoy bold multicolor filament with a glossy silk finish, this is a fun option that prints well and creates standout pieces.

Fungerar utmärkt att köra som generic abs på Elegoo Centauri Carbon i 160% hastighet. Ger något blankare resultat än vissa andra varianter. Prisvärd produkt.

Pedido enviado con rapidez y bien embalado. Biene envasado al vacio como otros rollos de filamento de esta marca que ya he comprado con anterioridad. Trae una bolsa de plastico para poder guardar una vez abierto (Se agradece el detalle) El rollo es de 500gr y pesa lo que dice. Referente al material he tenido que ajustar algo los parámetros de ajuste de mi Ender 3s1 ya que al principio haciendo algun test me dejaba hilos, pero poniendo la distancia de retracción a 1,5 y la velocidad a 35mm/s, (Es extrusión directa) con una temperatura de extrusor de 215º y la cama a 60, la verdad es que la segunda prueba ha quedado de 10. Sin duda volveré a comprarlo. Pongo foto de la primera prueba y de la tercera.

Ett av dem bättre TPU jag prövat

Filament de bonne qualité, j'ai déjà acheté cette marque et jamais de soucis, si l'imprimante est bien réglée tout se passe bien, la première couche adhère bien et la couleur est très sympa.

Un filamento muy bueno.Viene embasado al vacío para su mayor conservación y además viene con su bolsa para luego guardar y proteger de la humedad.Recomendado 100%.