Gizmo Dorks 1.75mm PLA 3D Filament 4 Color 200g Each Blue Green Orange Red

I read a lot of reviews on this filament and it seemed to me that there was quite a few negative comments. After using the filament myself, I felt the need to address those comments. 1). Color quality. I saw a few comments about this filament being dull and not vibrant. I did not find this to be the case. I liked the look of the colors and once they were printed they did not lose that appearance. The colors appear pretty much they way they do on the picture. 2). Filament diameter tolerance. I cannot speak to exact variations in diameter, but I can say the the filament appears pretty consistent. It fed into my printer without issue and printed very well. 3). Winding. Here was the one complaint that I can agree with. The filament is not wound with the same degree of accuracy and precision as most that I have bought. I can see where snags might happen. Now, saying that, I have not experienced any snags or tangles. 4). Quantity. It is four spools of 250 gram filaments each. It is advertised as such. I bought what was advertised and got what was advertised. I don’t understand some of the comments about the spools being small. I found it to be an excellent price for four different colors when my needs were small. If you need large amounts of a particular color, you should look elsewhere. 5). Print quality. I’ve bought filament from Amazon before and have had nothing but problems with it. This is not the case here. The filament prints out well and the detail is about what I would expect. Understand, I’m not a high utilization user. I print for fun. And what I find passable or good may not be in the eyes of an expert. I’ve included pictures because i think they will say more than I can. I bought this filament to make game pieces. It does this well. I’ve not found any uses yet for large prints. If all you are using this for is limited runs then you will be happy with this.

After reading the reviews regarding color accuracy, I was hesitant to purchase this pack, but I'm *very* glad I did. I've almost finished each of the four spools, and the quality has been excellent across the board. Additionally, Gizmo Dorks customer service was fast and helpful when I had a question before ordering. COLOR I'm not sure why there are complaints about color. My filament had strong color, which matched the described blue, green, orange, and red. In the review photo I've compared printed items to the authoritative color source-- Lego bricks. The orange filament is a slightly more yellowish tone than a "true" orange, but I also found the color to be more aesthetically pleasing than a bright orange. (Each of the filament colors also match the appropriate CSS color name, but Legos are always the answer.) PRINT QUALITY Excellent prints using an Ender 3 at 195 degree/45 degree hot end/build plate temperatures (bed adhesion, layer adhesion, and dimensional accuracy). No issues with filament diameter in any of the spools. TIP: store the spools in an airtight container (or zip-top freezer bag) with the desiccant pouches the spools shipped with. This will reduce the chances humidity will compromise the filament quality. CUSTOMER SERVICE I emailed Gizmo Dorks customer service get a copy of the Safety Data Sheet (SDS). I received a follow-up email almost immediately, and I received the SDS the next day. This was amazingly quick and painless compared to many other vendors. CONCLUSION I'll be switching over to Gizmo Dorks as my primary source for PLA filament. The quality is excellent, and the price can't be beat.

This is a great collection of filaments for those who occasionally do color 3D printing. Print quality is above average but not perfect. I won't use them as my go-to filaments for routine printing, but they work well to add a bit of color here and there. Honestly, I would expect other filament vendors to have these small, multi-pack, colored filament spools, but this is the only one I can find on Amazon.

Nice color variety without needing to buy several full spools. The filament is very springy, and tries to unroll the spool while loading it. I also found that it prints fine, but not as good or forgiving as some other filaments I have tried. It took some tuning to find the right settings on my Creality K1 Max, the generic profile didnt work right off the bat and I found I had to turn the speeds down slightly. If you are familiar with changing the settings in your slicer, you will have no problem using this, but do expect to do a temp tower or other calibration before you get going. Oh, I dont have a multi color system, but if you do (like the Bambu AMS or Creality CMS), these spools are small. They probably wont work in your multi color system without respooling.

I bought the 4-Spool sample PLA 6 Years ago and have used many other Brands but, this PLA always prints excellent and the finished prints are the Best! So good that I save it for printing stuff needing higher quality printing. The only downside is the higher Cost compared to some others. I store it in a Tub with a Mr. Coffee set with a On/Off Timer to keep my Filaments Dry. Have NOT broken any PLA, PETG, ABS, TPU Filament in the past 15 Years! I printed this morning with 6yr old Blue (photo)

While they are a smaller roll, I've been through three sets of this so far (12 rolls) Printed at different heats, different layer heights and no issues at all. I paint my projects, so color isn't an issue, but they are nice and bright if you want to print and go. Only one roll snapped, but it was with a few feet only left on it so I'm not too worried, a simple splice to other scraps and good to go It's a good option if you don't want to worry about larger rolls getting wet in storage or such because you haven't used them in a bit. Good stuff.

This has not been good filament. It it’s rubbery and does not put off the prints or snap off well. It’s bendy and very frustrating. Don’t recommend .

Works great for my project

Si necesitas colores variados para tus impresiones y no quieres gastar en carretes de 1kg de filamento, esta es una buena opción. De repente hay que estar pendientes de la impresión porque a veces pasa que el filamento viene un poco más grueso y se puede llegar a atorar (me pasó sólo con una de muchas impresiones, por lo cual no creo que sea un problema tan común). La adhesión entre capas es muy buena, la fuerza del material es buena. Los colores me parecieron muy bonitos. La usé en una Ender 3 Pro con 210° en la boquilla y 70° en la cama, fueron los ajustes que mejor me funcionaron para adhesión a la cama y adhesión entre capas, además de que da una pieza robusta y resistente. Sin duda volveré a comprar cuando se me acabe.

Heel leuke aanvulling bij de 3D printer, Toybox

Very nice colour pla. Prints nicely

Very good and stable product

works