All-Fit Automotive Bumper Scrape Guard – Universal Front Splitter Lip Guard – Easy-to-Install Skid Plate Kit for Lowered Cars (10’ L x 1.5” W)

It comes with everything you need to successfully install. Great look (although you don't really see it). Great adhesion it comes with adhesive promoter and this thing is pretty low profile. Perfect for my lowered car and hopefully enough protection for my carbon fiber front lip.

Great product! Clean looking installation. Much better solution than any of the "popular" similar products out there. Very glad that it includes 3M adhesion promoter, very effective.

Started out very happy with. Was very easy to apply. Was made of a true rubber like material. Followed directions exactly. Cleaned area very well, including alcohol. Let dry. Peeled back covering exposing adhesive small section at a time. Once applied went over several times applying pressure. Used hair dryer as instucted to further enhance adhesion. Let dry for approximately 40 hours. My daughter went to the store, upon return the end had started to peel off for about 3 inches. I. The reviews it looks like others had similar issues. This was put on a 2025 Toyota Camry from lower air dam. I had about 1 inch left over. To be fair there was not a lot of surface area in spots for it to adhere to. It looks very good on the car. Like the idea that because it is L shaped it covers both the underneath and front of the molding. I will take some paint protection food and try to secure the ends better. I would definitely order again if I could figure out the adhesion issue.

I installed it on my new lexus. very easy to install. very durable

I have a front splitter which is very low and has already cracked so was looking for something that will help provide some protection. I first installed another type of scrape guard (the set of plates that looks like a row of 10ish triangles) and added this underneath at the same time to provide a little more depth as the splitter has a larger lip.This bumper guard comes in one long roll with two strips of tape already applied and also includes packages of promoter and wipes, plus some gloves (but I just used fingers to apply both). The roll of bumper guard was more than enough to completely cover the bottom of the front splitter with plenty left over if I want to do anywhere else.Unlike the other type of scrape guard be aware this does not really bend/curve too much. Luckily my splitter wasn't too curved but it did result a few light kinks. Maybe it was due to the cooler temps in the garage and/or the bending but it didn't properly stick a few places. However I just used some clamps for a couple of days and that seems to fixed it.Will provide any updates after a few months of usage but for now it looks good and hopefully provides better protection.

They say this is a bumper anti-scrape guard, but I saw the width and got it for molding along the doors of my truck. I wanted it to fend off the doors of other vehicles that sometimes strike mine while in a lot. I used this at the best height to prevent that, along the front and rear doors on both sides. I made my straight line with masking tape, dry-fit this molding below that and trimmed it to size with a new razor knife. Then I peeled the backing off as I went, tacking it down. When I was sure it was just right, I rolled it with a rubber roller.It is 3M adhesive and I trust that, and it comes with cleaning wipes and adhesion promoting pads as well. I washed the truck, wiped the application area with the cleaning wipes, followed with adhesion promoter, and then the molding. It’s always a good idea to wait a week or so before taking it through a car wash.By the way, this says it’s 1.5” wide in the headline, but in the “product dimensions” below, it says “0.5”. The 1.5" measurement is correct.This is a 10-foot length, so you’ll want to make sure that is enough for your needs.

I got this scrape guard kit to apply to the bottom of the front air dam on by '89 BMW 635 CSI that had been damaged from repeated pavement scrapes over time. I'm waiting for the car to come back from a repaint before applying it, but the roll of scrape guard is more than enough to fully cover the bottom lip of the spoiler and just the right width. I've used 3M adhesives before and the protective strip should stick just fine to the newly painted surface. Overall I'm very pleased with this product. When my car comes back from paint I will get it installed and comeback and update this review as needed.

Watch the video in install it the way they do and it's very good to keep your car from scuffing up whenever you pull into places