Nilight LED Light Bar 2PCS 60W 4Inch Triple Row Spot Flood Combo Lights w/Wiring Kit for Fog Driving Work Lighting on Off-Road Truck Tractor SUV ATV UTV Golf Cart Boats

I bought these lights to install on my snow blower because I enjoy moving snow around in the dark soooo much. Installation was quick and straight forward though my snowblower has electric start and a 12v battery so that makes the electrical installation very easy. I've seen others mention running their lights on their power tool batteries via adapters sold here on Amazon if you don't have an existing electrical system to rely on. The lights are very bright with a wide angle and the difference it makes is impressive to say the least. The electrical draw doesn't seem to effect snowblower performance or battery charging in any noticeable way. I'm writing this review at the beginning of my 2nd winter using them and I haven't seen any corrosion or wear at all. I would highly recommend them to anyone who enjoys clearing their driveway in the dark after work as much as I do. The attached picture shows the single LED light included with my snowblower in the top image. The bottom image shows the difference when the flood lights are turned on. Fwiw, the camera I took the pictures with doesn't do a very good job showing how much brighter the fog lights are compared to the stock light.

awesome and bright easy to install!!! 10/10 recommend

Amazing LED light there are so bright i drive my Go Kart at night now is just Awesome!!!

I bought these LED pod lights to use as ditch lights. My truck has red accents, so being able to get pod lights in red casings was awesome. These lights make a significant difference (improvement) for my peripheral view while riding trails. You can see in the pictures the difference between having the lights turned off and on. They light up the sides of the trail with both spot and flood lights. Although the wiring harness is very robust, this is where I have my only issue. The harness seems to be made for the lights to be used as fog lights, instead of ditch lights. The reason I say this is because the harness was too short to reach across the engine bay and connect to both lights. It was only short by about 8 inches (reaching across a midsized pickup) so I simply spliced in some extra wiring to make it work. This doesn't lower my overall rating though as I said I'm pretty sure the wiring harness was made to be used with fog lights. Overall these lights have been working great for me, were very easy to install, and are available in different color options. So I would highly recommend these to anyone interested in them, with the caveat that small adjustments might need to be made to the wiring harness based on placement.

Installed on my red farm tractor as rear facing work lights. Specifically bought these lights because they are red and metal, led lights, and look tough. Only disappointment was the short wiring harness. Too short to mount the lights on the rear of any kind of vehicle. Be prepared to use your own wiring, connectors, fuse, switch etc. But the lights themselves I like. I can work in the dark on my tractor with 3-point implements and see quite well behind me.

I bought these lights to install onto my Bad Boy Magnum MX zero-turn mower. The included wiring harness with switch and relay was a big plus and reduced installation time. I ended up not using the included switch, as it didn’t fit the hole I wanted to use. To mount the lights, I went on Etsy and bought heavy duty front wheel spindle mount adapters. They basically clamp onto the spindle housing and then provide a 3/8 hole for the mounting stud on these lights. There were no mounting instructions, but it was pretty easy to figure out. On the wiring harness, pay attention to the spade connectors. Some of them were not crimped tightly requiring me to crimp them down some more. Installation was completed and the lights are bright and crisp. I was able to cut some grass during darkness as the led lights guide the way forward. Would recommend, it seemed like a good value compared to “factory” brand led light kits costing over $120.

The black ones said they would fit my 2007 honda 400ex but these red ones did not. I wanted the red ones to match my bike so I bought these thinking I'd mount them on the 1" front bumper with this mount kit for $17 on Amazon. Auxbeam Light Bar Mounting Bracket Kit 1 inch Bull Bar Roll Cage Clamps Mount Clamps Universal Holder Kits for Led Hid Light Bar Jeep Wrangler Trucks Off-Road (2 pcs) Decided I'd rather put them on the handlebars so They're more of a spotlight. My handlebars are 7/8" instead of 1" though. I tried wrapping the supplied adhesive foam pads with black tape to make up the 1/8" but it was sloppy. Luckily I'm a machinist lol so I made some aluminum adapter bushings. Worked out great, pretty sturdy, probably even better on the correct size mount bar lol. Just hope I never roll the bike lol! Drilled a .812 hole in my aftermarket handle bar indicator plate (where the key, neutral, & reverse lights are) for the switch after wiring everything, which was a breeze with the supplied harness! Put heat shrink tubes over the connections and then black tape for good measure! Much better than the factory headlight, took my first night ride last night! 3 thumbs up for the brightness & price!! Hopefully they are really waterproof! I snugged down the bolts on the housings a bit, fingers crossed!

Excellent product. Built to last!