Eureka 50mm Espresso burrs. Fits Eureka Mignon, Nuova Simonelli Grinta, MCI, MCF, Gaggia Baby, Macap M2. MAC50 (Espresso)

The Eureka 50mm Espresso burrs are a perfect fit for my Eureka Mignon Crono. Grinds are consistent and flavorful. Easy to install and clean. Highly recommend for any espresso enthusiast!"

had to buy these burrs, as i sold my former espresso grinder which was a bottom level espresso grinder to put it kindly, and bought a eureka chrono model. they formally were made in italy and were able to grind fine enough for espresso,but no more. my new model (2024, year of mfr.), was made in china and uses strictly filter grade burrs. simple to install the espresso burrs, no alignment issues, straight forward remove and replace. cost is reasonable, considering the much higher cost of buying a out-of the factory, eureka espresso -ready grinder. fully satisfied with the upgrade and money well spent.

The original burrs for my Eureka Filtro were NOT the Filtro burrs (why??) and I was always a little disappointed in the grind consistency for for coarser grinds, considering that’s why I bought the Filtro. Well, now I know why! With these correct burrs now in my grinder, I’m getting much better results and the coffee does taste much better!

I bought an Eureka Mignon Manuale which has an espresso burr. Since I mostly make V60 and French Press, I bought this to replace my espresso burr. It is a perfect fit

Overall, a great set to replace the filter buffs that may come with the Chrono grinder. Can be a bit tricky to adjust to the right grind, so be prepared to go through a decent amount of coffee, but once on the right setting, you will be getting some of the best tasting shots. Enjoy the cup

Apparently, there is very little difference between the $209 Eureka Mignon Filtro coffee grinder and the far more expensive Eureka Mignon espresso grinders other than the switch (the Filtro uses a plunger switch with out timing feature) and the burr blades themselves. After research, I discovered that you can simply replace the Filtro coffee grinder blades with the Eureka Mignon espresso grinder blades (be careful in ordering as there are two sizes). I was able to order these OEM burr grinder espresso blades to replace the coffee grinder blades on my newly purchased Filtro grinder to create a poor man's Eureka espresso grinder for about $150 less than Eureka's least expensive espresso grinder. Works great!

Highly recommend.

Received knockoffs without any Eureka branding on burrs. Grind profiles obviously different from originals and results were terrible.

New burrs are wonderful for my grinder.

Received the package and was excited to change the Filtro burrs from my Eureka Mignon to espresso burrs, but felt right out of the box that these burrs were dull. I tried them out and they could not grind for espresso. Contacted seller regarding this and they said it was a problem with my machine and that it wasn't "calibrated" for espresso, even though it can grind for espresso just fine with the regular Filtro burr set. In the end I had to contact Amazon customer care to get a refund for a faulty product, but overall bad experience with this seller.

Il mio macina caffè Eureka mignon è assolutamente rinato, credevo di essere io il problema nel non riuscire a trovare la giusta macinatura, l’ultimo tentativo prima di cambiarlo è stato acquistare queste macine, che dire, tutto un altro pianeta! Ottima macinatura con scarsa produzione di calore!

Espresso bıçakları Mignon filtro için aldım. Tam uyum sağladı ve Espresso ayar kademeları artı.

The burrs feel of a high quality. They are sharp and well machined. But please note that these are exactly 50mm, but the original for my Macap M2 was 49.9mm. The description does list it as compatible. The tolerances are quite tight and it did not fit in the part that could but screwed off. I was able to to press it in by heating the receiver end in the oven (80°C) and putting the burr in the freezer (-20°C).