Pine Ridge Archery Wishbone Bow String and Cable Dampener for Noise Reduction and Vibration Control

Purchased these to try in lieu of the Monkey Tails. They are lighter @ 13.5 vs. 17.0 grains so your string will have less wait on it, so depending on how far you shoot and what group size you want, it may change your ballistics noticeably. Thus far they have held up just as well as well as the monkey tails and perform equally well (or better) at dampening the string vibration; at least to my "calibrated" ear. If you still want "monkey tails", Zebra now sales them here on Amazon: Zebra String Silencers Pack, Black Installation Note: If you find these, or the others, hard to install, first soften them up a bit by stretching them several times prior to installing. I do this using a #2 phillips screwdriver placed through the eye of the head, and then pull on the tail(s) to stretch them several inches. Second, place it on the string and insert the tails through the eye, insert a #1 phillips screwdriver through the eye, from the opposite side you inserted the tails through, and then stretch the eye slightly while pulling the tails through and securing the dampener. This requires the dampener less stretching of the dampener during install; thus, extending the useful life and preventing premature failure.

I have a Hoyt bow with hamskea verifier peep sight. It made a twang sound after the shot. These silencers made it dead quiet. I'm amazed at the noise reduction. I highly recommend this product

The cable dampeners were easy to install. I was worried after reading some reviews about installation issues but I didn't have any problems. I used a needle nosed pliers inserted through the hole and grasped the "tails" and pulled the tails though the hole. Also, did a little "finger massaging" to get the lip through the hole but it wasn't difficult. Seemed to work just fine. I like that you don't have to remove the string to install the dampeners. As far as dampening the vibration I'd have to say they worked ok, but nothing significant. Bows are so different so if you want to give these a try I think it would be worth the investment to try these out. They are an easy and inexpensive attempt to silence the vibration noise. They may work great on your bow.

I've got an older Mathews solid limb. Getting hard to find limb stabilizers for the solid limbs anymore so I wanted to try these after installing new string and cable set. They ARE rather tricky to install without ripping them, like several people have said. I was having a few issues trying to get them installed, but I finally was able to get a pair on WITHOUT breaking any of them. Take your time and use care to pull them through gently yet completely. They work GREAT at this time, not sure about how long they'll last, but the bow has quieted down a large bit. Would recommend them if you want quiet your bow and also stop the vibration too. Not sure if they slow down the arrow much or not because I haven't chronographed it to know.

I've had these on my bow for about a month now. These work just as they should reducing the vibration of the cables on my bow. Install wasn't terrible, but not easy either. If you use needle nose pliers to thread them through themselves, and are not afraid to really grip down and pull snug, they pull through no problem. They do not require a bow press to install and are made of a very tough rubber that I expect to pass the test of time. I will likely buy again for my next bow. I like them better than the string leeches I used to use.

awesome product ,really going to help maintain that string snap , i shoot my bow all most every day have a lot of arrows down range after installing an they stay in place an work well !!!!

I put these on my Darton Consequence, which is a pretty quiet bow but had just a touch of string "twang" after the shot. These things quietened it down perfectly. They are a bit of a bear to put on but really not that bad. They are extremely tough so don't be afraid to yank on them or grab them with a pair of plyers. Took me maybe 2 minutes to put both on.

I can’t believe how much quieter my Hoyt is after putting two of these on. I would not have expected this much of a difference and I am beyond pleasantly surprised with how effective this product was. There was no discernible difference in arrow drop in case anybody was wondering (checked at 60 pound draw 30 yards). Easy to install to, 2 minutes and I was done. Needed nothing but my fingers.

I takes a bit of pulling to get the dampeners on the string and cables but they are definitely made tough enough to take the pulling! Haven't measured the decibel difference but it is noticeable during the daily indoor shooting I do over the winter.

Son muy buenos silenciadores, de fácil instalación y a muy buen precio

Easy to install and affective .

Good

They went in great one broke tho