WEN DC1300 1,300 CFM 14-Amp 5-Micron Woodworking Dust Collector with 50-Gallon Collection Bag and Mobile Base , Black

Works great for fine particles from woodworking. I roll it near where I’m cutting just outside the garage. You will still get sawdust of course but the lighter airborne dust is what this will pull from the air so you’re not inhaling it. Much better than using a fan blowing away from where you are working g thinking g that is helping. Quality of this is great & was fairly si Ple to put together either no issues. Really like the base & caster wheels for maneuvering around or I can simply turn on where it sits to clear the air. It’s not quiet but not too loud. I wear ear protection when cutting anyway as you should so sound is not an issue.

Love it and it’s perfect for my small shop, easy to assemble, the base being on wheels makes it easy to move around or out of the way when not in use , great suction and price

Overall, it's a terrific machine and a great value. It took 99% of the sawdust my table saw produced, with just a tiny bit on the saw table top. Nothing on the floor or anywhere near the saw. Very good with the wood cutting bandsaw but more like 85% capture. I will need to use a second hose for dust capture in a custom mount in the table area of the bandsaw, and then I should get close to 99%. Four suggestions for future improvements (which is why I gave it 4 stars instead of 5): 1) Make the 3 vertical supports for the housing that connects to the bags heavier duty. 2) Make the upper arm that holds the 5 micron bag adjustable height so if you need to roll the machine to another part of the shop and there is an overhead ductwork clearance problem, you can quickly and temporarily lower that bag support as much as 6 inches or so. I am modifying mine accordingly. 3) Put a pigtail style hook at the end of the upper post where the fabric loop of the 5 micron bag hooks on. It can easily slip off, so I taped mine to keep it secure. 4) Improve the instruction manual. It doesn't make much sense to make attaching the handle the last step AFTER installing top and bottom bags, if you need to then uninstall the ring holding the top bag to reach inside the steel ring for fastening hex nuts on the inside But overall it does a great job. Definitely a good investment and it will leave your shop air much cleaner and far, far less clean up work afterwards.

I have used this Woodworking Dust Collector extensively for several months. It was easy to put together and continues to work great. This dust collector along with the WEN 3410 3-Speed Remote-Controlled Air Filtration System I purchased through Amazon greatly reduces the wood dust in my shop. I still wear a disposable respirator while cutting wood, but can take it off soon afterward because of how well the WEN dust collector and air-filtration system work.

Works ok and a heck of a lot less money than some of the other brands that come off the same production line.

They did it again folks. WEN has not let me down when it comes to affordable quality tools. This puppy is super quiet but yet strong and efficient. MUST BUY WHILE YOU CAN

Most of my tools are 2 1/2 inch outlets. So reducing the size of the duct reduces the ability to pull the saw dust from the tool. I purchased a Grizzly 8” Jointer with a 4 inch port. The Wen Dust Collector works great and is quieter than the shop vac. Getting the plastic bag installed was a challenge. I hooked up a Vevor dust separator so it will be easier to empty out the sawdust.

The WEN DC1300 is a capable dust collector, especially at its price point. I've connected the unit to a 6 inch full sized jointer and a 12 inch surface planer with a 10 foot hose and it pulls in %99 of all of the chips and dust produced. I've also connected it to a 14 inch bandsaw with about a %95 capture of the produced sawdust, which was better than I had hoped for given the complex geometry of bandsaw interiors. The build instructions were decent enough as was the fit and finish. A finer mesh on the filter bag would have been nice, but all-in-all it's hard to beat this unit at this price point. If you don't have a big budget and need to have a dust collector I'd recommend this collector.

facile à assembler, la puissance annoncé est véridique et le bruit acceptable À mon avis c'est un bon rapport qualité prix Le seul b molle est que le sac en tissus est en option.

I do not really like this dust extractor. It does not work well, the suction is not the best on it, and it will throw wood chips and dust out of the secondary hole sometimes. Not to mention it did not come with all the bits and bolts and they wanted me to pay to get them to Canada. I am absolutely not happy with this company as I was looking forward to using them but they did not turn out to who I thought they would be.