DEWENWILS Wireless Light Switch and Receiver Kit, 10A/1200W, No in-Wall Wiring Required,Remote Control Wall Switch Lighting Fixture for Ceiling Lights, Fans, Lamps,100 Ft RF Range, Programmable

I purchased the switch with 2 wiring harnesses and 2 switch with screw in receiver. I’m a licensed master electrician and have used a lot of different electrical products over the years but this by far is one of the best. Typically the part you dread is the programming but don’t worry about it with this product. Number one as I told you I purchased 3 different kits 2 screw in receiver with switch and 1 kit with 2 wired receivers and a switch. Each kit comes preprogrammed so the screw in self explained with switch there is no wiring at all with this kit it’s plug and play. The other 2 kits I have one screw in and one with 2 wired harnesses. This required reprogramming the screw in receiver which is the easiest programming ever. On the screw in there’s a button on it with power on press the button and the indicator light flashes continue holding button in for approximately 6 seconds and when blinking speeds up release button the old code is now erased. To program push the button and as soon as light begins flashing approximately 3 seconds release button and press the light switch on and then off the lights should light right away I programmed mine with 0 problems. Finally a product that I’m not swearing at the entire programming phase. I would say any DYI people out there no problem with installation other folks the screw in any one should be able to handle the wired ones are also very easy but some people aren’t comfortable with electrical work in this case consult an electrician. Take a minute read instructions and install you’ll be amazed at how easy it is. One lad note to the engineers and designers of this product my hats off to you I normally don’t have nice things to say about the design and build team because they tend to complicate and over engineer products this WAS PERFECT in my opinion I would shake everyone of your hands you truly deserve recognition for this project.

Excellent works great used with sconces and didn’t want switch on wall . This worked perfectly. Simple to install.

I bought this item because I could not get a wire from the lights to where I wanted a switch in my basement. I decided to wire it up and test it before I installed the lights. The lights turned on just fine, but would not turn off unless I got the switch within a few inches of the receiver. I tried every variation of holding the switch different ways to changing the angle of the receiver and it just didn't work unless it was close to the receiver. I couldn't figure out why it would turn the lights on from any location but would not turn them off. I returned everything and bought a Linptech R10 receiver with a switch and it worked great, and the pushbutton did not even require a battery! I also bought a separate receiver and linked the two in the app and now it switches off two separate lights with the push of a button. It looks like Linptech just came out with this new model because the one I first saw had a gaudy button, but the R10 is a more traditional flat button. It is more pricey, but it actually works! And the Linptech one can be connected to an Alexa device too, if that floats your boat. I can't do that, because we named our daughter Alexa (she's 16) before Amazon came out with their equipment that listens to everyone's conversations. But I digress, the bottom line is don't buy the Dewenwils equipment unless you want to be frustrated and have to go through the process of sending it back and buying a different one.

Remote receivers fit inside a standard electrical box behind two wall sconces. Be aware that the switch mechanism is a surface mount only, no option to have it fit inside a standard electrical box. See picture how it then looks next to a standard switch plate. Sooo...close to being a five star. With this much technology packed into a very thin circuit board, they would sell me a lot more of them if I could have it fit behind a standard wall plate. I purchased the two-receiver package, and both receivers came pre-programmed to work in unison, although periodically only one unit will turn on, causing me to have to push the switch to off position, wait a few seconds, then push it 'on' again to have them both light up.

I have two rows of led lighting in my man cave that have to be turned off in order to watch my theater projector. Call me lazy if you like but I had remotes for everything for my projector and screen right next to my recliner. Now with these installed I no longer have to get up and turn out the lights. If you don’t want to install smart switches then this is the way to go. Awesome value also. Installed in about 10 minutes each.

I gave this a three start rating because even though the switch works, it does not work very well. I stood between the switch and the sensor which are placed about 6' (six feet) apart from each other, and it works intermittently. It doesn't seem to want to turn the light off; I have to be depressing it multiple times before it responds. If I didn't already cut on the wire when I was installing it, I would've returned it and try something else. Honestly. So, I had to place the switch/remote in a position where I had no choice but to, just to make it work. Very disappointing. . . Installation wasn't an issue, and the size is the same as any other switch. No idea about what the battery life if or will be just yet; I'll see what happens in a couple of months. . .

This item obviates the need to hardwire lighting fixtures to switches. It includes small RF receivers that need to be tucked into each lighting fixture itself (ie its in-wall electrical box underneath). The RF controller switch looks like any other wall switch and can be mounted anywhere within RF “hearing” distance of the receiver/s. BTW one can easily by-pass the switches by using a WIFI/RF controller (eg: Broadlink Hub+APP) that first “learns” the on/off RF codes to its memory.

The wireless switch quit working after 2 days. Changing the battery did not help. One of the receivers is defective, causes the lights its connected to to blink on and off randomly. Not a good product.

I ordered the single switch with two receivers. Installation was a breeze. Turned off the power, connected the existing white wire to their blue and existing black wire to their red. I hooked up a test light to their black and white wires and turned the power back on and the receivers worked immediately when I clicked the remote switch. The only negative is the screws provided to mount the remote to the wall really have to be tightened down so they don't sit too high and block the remote latching in to the frame.

I found the instructions a little confusing, not north american terminology, but it works great, thank you

J'avais un plafonnier qui fonctionnait avec une chainette, le mécanisme est fragile, donc remplacé pour ce système sans fil! Ma conjointe est ravie. Facile d'installation.

I had bought three of them and none worked properly. When I contacted seller claim if there is any metal parts around the switch’s receiver, it will interfere with switch RF. Considering some switch boxes and the most light fixture trim are metal, so these switches probably do not work properly in most cases.

Facile d'installation, fonctionne parfaitement. L'interrupteur es de qualité limite