Hogue OverMolded Rubber Grip for S&W J-Frame Round Butt

This grip is a jewel. There is the saying that "God created man but Col.Colt made them equal". Well here's my saying "Smith and Wesson made an impractical revolver but Hogue made it practical. I'm talking about S&W's model 340PD. This revolver weighs 12 ounces. I bought it to carry while jogging or riding a bike. I could hardly shoot this revolver because the recoil was so severe. In my hands this revolver was uncontrollable. After searching the net for a solution I came across the Hogue 60020 centennial grip. First I had to figure out what a centennial was. I thought S&W brought them out long ago and didn't realize people referred to the all smith's with a concealed hammer as centennials. Once I got that settled I realized I had 2 centennial models, a 940 J frame and the 340PD. I ordered the Hogue grip and received it with-in a week. Following the instructions and ignoring the instructions for the S&W body guard, which this grip also fits, I found that it slipped into place rather easily. The hardest part was getting the grip cap into place. That took a few minutes. When I completed the task what I had was a grip that I could still conceal but was a complete transformation from a shooting standpoint. There was padding at the web of the hand, finger grooves. light weight, and thin yet some how comfortable. I took the gun out to my back yard range and started putting some plus P 38 specials rounds through it. The recoil was controllable and repeat shots not difficult. Plus the knuckle on my trigger finger did not get banged around. Now I can carry my 340PD with confidence. I did try a couple light load 357 mags in the revolver and quickly decided their not for me in this type of revolver. I was very pleased with this Hogue grip. I must add a second comment. I immediately ordered a second set of grips to put on my 940 J frame revolver. As easy as the first set of grips went on my 340PD the second set of grips for the 940 were just the opposite. I had to struggle and struggle trying to get them in place. I don't know what the hang up was but I finally got them on. Perhaps the grip pin on the 940 was a little too long. Once in place the grips worked to perfection. I not yet courageous enough to take them off to see what the problem is. For now I have two wonderful grips on two revolvers I carry frequently. Only now I feel a lot more confident in carrying them thanks to the Hogue 60020 grip.

Fits in the pocket PERFECTLY. Fits in the hand PERFECTLY, whereas the factory grip could not get the pinky on. Install was easy, no complaints. I liked it so much I bought a second one for my cousin to try.

Was as described and works well

Perfect fit on my Airweight. Installation was a breeze...hardest part was finding a screw after dropping it, lol. I can get 2/3 of my pinkie finger on the grip now. It added 3/4" to the grip, no problem there. The texture feels better than the original. Price is very reasonable. It looks good ... can't wait to fire it!! If you have an Airweight, buy it.

Fits perfectly on my .38 Special Model 642-1. I used the original frame pin, so there was no need to replace it as the instructions suggested. I gave it 4 stars because the clip that secures the grip arrived rusted. Additionally, my first order came with the wrong grip, and my second order was delivered late. Overall, it’s still a great upgrade for my daily carry.

Got it yesterday, installed it last night. INSTALLATION: Very straight forward. Read the directions before you start if you are not familiar with this type of work. This is a must for any who CCW's a S&W 642 Airweight (If you're unsure about this - it is the one for this pistol) This has given me the grip I was missing after all these years of having this as a CCW. I wear a medium/large (more toward medium) in most gloves and the stock grip of the 642 was a like a dang mule kick when I fired +P rounds. I've been shooting for a few years so I am accustomed to recoil - but anyone else who shoot this would say the stock grip hurt their hand.I will be at the range this weekend so I will update after, but I have handled this grip quite a few times since I installed it, so I hope it performs as well I i feel it should.Ok, now for the initial impression: FEEL (compared to stock) - definitely narrower, but with the additional length it feels more natural. I can now use all three fingers. This is a firm, rubber material that gives my palm some padding, while allowing my fingers to grip the gun without too much manipulation. CONCEALABILITY: Personally, I do not see an issue with the new 1 and 1/2 inch inches or so. Pocket holster (Uncle Mikes Size 4) continues to work. I wore this in my waist today for about an hour and it was unnoticeable. Felt more secure to be completely honest since the rubber and length hung onto my pants waistline better than stock. SIGHT PIC: My muscle memory will definitely be re-trained. I already noticed I need to cant up more at the wrist (from a standing point shoot position) and same from hip shooting position. Not a lot of change, but some nonetheless. I gave this a 5 right now since it arrived quickly and my initial impression of this is, absolutely yes! If anyone asked for my recommendation. Did I say I really liked this so far?

I bought these for a Diamondback SDR 357. Manufacturing is a different fit from the one I bought over a decade ago. The Company rep agreed with me and advised to get the rubber grip vs the nylon grip. I did and it worked out. 5 stars for smooth return , hassle free

OK for perhaps someone but not conducive to conceal carry or taming a standard load in S&W 340 PD 357 Mag 125 Gr. I have 2 of these and returning the third one I purchased. Advice is to use OIL and a rubber mallard. Definitely use the supplied dimensionally protracted roll pin supplied with grip. This grip after, arduous install, is OK if you are just doing shooting range and have neanderthal hands needing K frame ergonomics.

Très bon grip et de qualité, parfait .

タナカ m360Jに装着しました。 懸念されているガタもなく装着もコンコンと軽く叩くだけでストレス無く装着できました。 非常に満足です。

Con le guancette originali piccole in legno lucido dopo 5 colpi di 357 avevo i capillari rotti tra indice e polli, controllo durante lo sparo non ottimale (avevo anche le mani sudate e con l'impugnatura lisca non aiuta), con questa grip in gomma ho risolto tutti i problemi, presa saldissima, si contrasta molto meglio il rinculo e anche con mani sudate nessun problema.

所有しているJフレームのほとんどにボーグのグリップを着けています、価格も手頃ですし、取り付けも簡単で見た目もプロ仕様に見えるしカッコいいです

3インチのバレルとバランスが良いと思います。 装着にはハンマーのような叩くものが必要です。 またタナカのようなグリップにウェイトが入っているものはネジを取り付けづらいです。