Leapers MT-RSX8S Inc., UTG Ss Picatinny Riser Mount, Black, 0.83"

Lightweight and rock solid. Comes with a torx wrench and a spare mounting bolt in case you strip one. It looks good on the rifle and doesn't move under recoil or from moderate bumps. Good quality finish holds up well. Excellent mount for Bushnell TRS 25 and Primary Arms mini red dots. With Magpul MBUS sights, the 0.83 inch riser gives you a nice lower 1/3 cowitness. The sights sit below the dot in the lower third of the glass when looking at the dot alone. The 1.0 inch riser will just barely cowitness, but you can only see the very top of the front sight blade when using the iron sights with MBUS and the aforementioned red dots. The 1.0 inch riser was too tall for me, couldn't see enough of the front sight post, and much of area around the post is blocked by the emitter with the TRS 25. I've not tried the 0.75 inch riser, but I suspect it offers an absolute cowitness with the TRS / PA / MBUS setups. Pro Tip: If your iron sights are zeroed in, you can easily zero in your red dot without firing a single shot. Just look through your iron sights in perfect alignment while adjusting the elevation and windage of the red dot so that the dot sits on the top center edge of the front sight post. Make sure you are looking through both front and rear sights in perfect alignment when you do this. This works regardless of the height of the mount or type of cowitnes, and some people think this is cowitnessing. It is not the same as an absolute cowitness, which might explain the conflicting info on riser heights and cowitness. All correctly zeroed iron sights and red dots will appear to be cowitnessed when looking through the iron sights, regardless of the height of the riser. However, with a lower 1/3 cowitness, the dot is also visible above the sights when you move your eye above the iron sights.

Good Quality and Design, But need to read more for an issue with being too tall if using iron sights for back up. …the product is well deserving the highest rating of five stars… it is manufactured in Taiwan and reflects the years of experience manufacturing quality tools for the trade industry (unlike cheaply engineered by PRC companies like Monstrum) this is the second one I purchased to be used as riser block for a RDS on my ARs. The first was the .5” height and it was installed on an AR carbine with a Vortex Defender ST with Magpul BUIS as backup sights. The set up is comfortable with the Magpul carbine stock and is “co-witnessed” with the iron sights. I now find I don’t crawl on my stick as much as when younger and wanted to try a hight mounted sight… so I ordered a taller one fir my other gun. My second one is the .83” height… to mounted on the same type gun and sights… when installed, found height very comfortable for my head position… BUT, the height took the iron sights out of play… the front sight was no longer visible… eliminating the back up function Was going to order the .75” version but decided to go with what already a known workable height (.5”) Maybe with a different RDS with a bigger window the higher base may work… not with the Vortex Defender ST

Works as advertised, was a breeze to install, and holds fast. I used blue loctite on it, so I'm not worried about it coming loose. Love the .83" height for co-witnessing. Overall, it's a great budget riser. I use mine with a Bushnell trophy micro-dot.

I bought this riser as a mount for a Bushnell TRS-25 red dot, which seems to be the best choice for budget optics. I went with the .83" for absolute co witness of iron sights, but ended up putting the whole assembly on a 300 Blackout pistol that doesn't have irons yet, so I could take it to the range and shoot it. The good: It's inexpensive, and light. The machining and finish were fine. The bad: The screws keeping the mount on the pic rail worked loose under the recoil. After 40-50 rounds fired, the whole assembly was in danger of falling off the pistol. After I got home, I backed the screws out, and applied some temporary (blue) loc-tite. I think it should work, but I haven't tested it since. I would recommend using loc tite before heading to the range.

Love this mount! The looks, how compact it is, the light-weight, the finish. Seems super durable & quality machined (a lot of "extra" material has been removed to keep it as light as possible without compromising it's integrity). The logo is nice as well, the sizing & that it's etched. It has 2 mounting screw instead of just 1 like some mounts do. **MOST IMPORTANTLY: I'm using it on an AT3 RD-50, when I purchased that sight I opted for the 1" riser that stated it would be ⅓ lower co-witness, it was *not (using Kriss USA lo-pro poly BUIS). I couldn't see my irons through the sight at all, with the UTG mount on the same optic, it is a true ⅓ lower co-witness, fits the optic perfectly, & has an additional mounting screw. The only "con" which I can't really even put in that category is the fact it must be mounted with a tool/wrench intead of a QD mount (which I know they offer those options, which is why I can't knock it).

A surprisingly sturdy and well built riser. Metal feels great, and fits very snug onto my airsoft rifle. Comes with torx screws as an added bonus. Would recommend for anyone looking for a no frills riser.

I was looking for a cheap way to mock up a 2.26 mount instead of diving head first into a Unity FAST riser and magnifier mount, a cowitness red dot on this is pretty much the same height give or take a fraction. Naturally when I liked it and bought a FAST mount I kept the rear rail section on to act as a magnifier riser so the same magnifier will work with my FAST mount and my other cowitnessed dot on a different upper. Quality wise theyre pretty good, made in Taiwan according to the package, no tooling marks to be found after a quick look and they lock up tight and snug. I still dont think its a good idea of use this as a permamant riser on a duty gun, but for a magnifier, air soft, or a mockup I see no issues with it in the slightest.

It set my bushnell red dot higher then my tacticon pop up iron sights

I'm actually quite surprised with the quality of this riser for the money. It's small, lightweight and feels very sturdy. The 2 star headed screws are solid (wrench is included). The 0.83 gives you perfect co-witness with the Bushnell trs-25 on AR platforms. I use to go with the cheaper UTG riser which is also nice for the money, but this one is worth the extra 10 bucks or so. The 2 screws design is better and the mount is much smaller, slimmer and nicer looking. The TRS-25 combined with this riser gives you quite a decent optic for the money that really can't be beaten. Next step up would be a holosun micro or sig romeo 5, but they go for more than twice the price of this combo.

Sehr hochwertige Verarbeitung...leicht und funktioniert. Top!

Works great to get my little reflex optic up to proper 1/3 co-witness. Seems really sturdy but nice and light.

Leicht zu montieren und hält einwandfrei

Passt hervorragend auf Picatinny Schiene, satter Sitz, kein Wackeln, Mechanisches Visier weiter nutzbar. Für kleines Geld große Qualität👍🏼👍🏼👍🏼