Nano Polymer Adhesive (50ml) - Ultimate 3D Printing Bed & Build Plate Adhesion - No Mess, Non-Toxic, Works for PLA, ABS, PEI, PEEK, Nylon, PC and More. Easy Application, Easy to Clean!

PRINTER: Creality Ender 3 V2FILAMENT: PLA HatchboxMODIFICATION: replaced leveling nuts and hot bed springs ($13) and borosilicate glass build plate ($14)ADHESION: amazing!! No more unstuck fails. No more warping and fails. It’s saved me from quitting 3D printing all together. Sometimes I still have difficulty with adhesion but I’ll just wash plate with rubbing alcohol and put a new double coat of this glue and BAM! It works like a charm.PRICE: Fair. - $19 for 50ml. It does the job and it’s SO worth it if you know how much of a life suck it is to get failed prints. Your bottle will last a long time if you only need a thin coat every 5-10 prints. With my double coats every 2-3 prints it will run out a lot quicker but still lasts a long time. I’m still on my first bottle (50ml) and if I had to guess how many prints (for me) it would last… hmmm… it’s hard to judge…. I’d say 200 - 400 prints or more depending on the amount I use. BUT!!!!! It’s soooooo worth it, no other method have worked for me (new build plate, glue stick, hair spray, and magigoo” brand glue- which did work at first but then failed). IMO: I think climate has a lot to do with adhesion. I live in Pacific North West where it’s wet and cold. (High humidity)REMOVAL: extremely easy, spray with rubbing alcohol (or alcohol pads) and wipe. May take several spray and wipes but comes right off! So easy. I rarely have to clean my build plate with soap and water because it comes so clean with 70% Rubbing alcohol.RECOMMEND: absolutely!Can also buy from: visionminer.com - but i get Amazon prime free shipping.any suggestions for me?Email: olivemeartsie@gmail

This stuff is literal wizardry. I've tried a handful or two of plate glue and this stuff works amazing. Nothing else really worked on my textured plate and everything to did left residue or caused surface blemishes on my parts that wouldnt go away. This stuff goes on pretty easy, you need to be fast to spread it well, because it dries fast and totally clear. The small bottle I have has lasted months and I only ever need to reapply before running nylons or something really warpy. It might seem expensive for a small amount but it works and it goes a long loooong way.

I am absolutely loving this product. I print mostly with PETG, along with some PLA, TPU, and PA (Nylon) on occasion. Anyone who prints these materials knows how tricky it can be to get consistent bed adhesion without warping, or conversely, having the filament stick too well and ruin the plate.I applied a thin coat of this Nano Polymer Adhesive to my stock textured PEI plate, and the results have been incredible.Easy Application: It goes on easily and dries down beautifully into the texture of the plate.Superb Adhesion: Filament adheres perfectly while printing. Even notoriously difficult engineering filaments like PA Nylon lock down tightly with zero lifting or warping.Effortless Release: Once the print finishes and the bed cools down, the finished parts are incredibly easy to remove. No prying, scraping, or wrestling with the bed.It completely takes the stress out of printing tricky materials. It is worth every single penny. Highly recommended!

I'm not new to 3d printer. I normally use cheap glue stick which works pretty well on PEI beds. Which is 8/10. It's affordable and works great.I recently got a new printer that's enclosed. Which prints on PEI bed, no issues with out glue. When I switch the bed to PEY (that smooth shiny stuff). For the life of me, nothing sticks. No turning up the temp, slowing down the print. I get a 1/20 successful print. I decided to give this stuff a try because I saw it on some random YouTuber's channel. OMG, game changer. This thing does not leave anything on your print, it does leave a little something on the bed. But man, I thought nothing I use would stick to the bed.Very few items I would give it a 10/10 score. This is by far the best one to use for your smooth surface beds. 50 ML is a lot and I should have gotten the smaller bottle because it's a bit expensive. I have two printers, and they are both 350 x 350 bed size, more than enough for both printer (since I don't put it on after every print).

Used with PEI sheet printing ASA over large area. 250x250x1mm. A very thin print. No curling during the print. Very difficult to remove afterward so be advised. If you compare this to something like gluestick it is in a completely different league. Brushes on and basically disappears. After application you are left with a surface that appears normal to the eye but grips like crazy.

Works much better than glue sticks and lasts a lot longer.

This is the best glue for 3d prints. It keeps the print attached to the plate and I don’t have to worry about it lifting. Definitely buy if your having issues.

Works great! Way better than magigoo or similar. If you really need something to stick, this is your solution.

This stuff is like bed adhesion god mode. Its too sticky, it has lifted the pei off every plate I've used it on, and i've diluted it with ipa, tried removing hot and cold.... its just crazy how stuck prints are with this stuff.I dont really mind as most of the PEI i used it on was pretty well worn out, and for a few drops of this to rejuvinate it to the point of being too good, even when i've diluted it down 3:1 is impressive.Will definitely buy more when I run out in like 10 years.

Yes, it's absurdly expensive for a 3D printing adhesive. That said, brush it on properly and a little goes a long way.Yes, it's by far the most effective 3D printing adhesive out there. When using this stuff with Nylon the limiting factor is no longer the bed adhesion. If your part is trying to warp the way it will do so is by lifting the edges of your build plate clean off the bed.

Goes without saying, this is the best build plate adhesive I've ever used. Fantastic adhesion. With a clean plate, and a good application of this stuff, I haven't had any issues with warping and lifting with any engineering materials I've used so far (PA, PC, PPS, PEKK, Igus, and more).The instructions recommend leaving "non high-temp" materials like ASA/ABS, PETG, on the build plate until it cools before removing the part. Having done this with some ASA-GF, I did scalp the PEI off my build plate, so maybe the adhesion can be a bit too good.My biggest gripe is the brush. For how much this stuff costs, the brush it comes with is a piece of junk. The packaging on the other hand was very nice. I would prefer they spend 20p more per item on a nicer brush, and 20p less on the packaging, seeing as one gets thrown away immediately, and the other is used every time I used the adhesive.I recommend getting some normal PVA glue or a fancier product like magigoo for day-to-day printing, and keep this stuff on hand for the fancier materials.

I'm shocked that it works as well as it does. The advertising, surprisingly, wasn't full of exaggerated nonsense. This is the perfect bed adhesive for even filaments that seem to hate existing.The best part? It's somehow also water-washable. It just comes right off the build plate under the faucet. Unbelievable. Well-earned 5 stars for this stuff.

First, the good stuff.It works. Prints stick to the bed, and then get unstuck relatively easily after cooling down. For the most part. I have had a few occasions where scraping was necessary but that’s to be expected with some materials.The bad: mainly that applying the product is extremely awkward. The way they tell you to do is by drawing a cross and a circle covering the print area, then using the included brush to spread it. The “brush” is a tiny one, with half a dozen stiff nylon bristles. The adhesive is very liquid. The brush barely spreads it over a centimetre - it has no chance to spread it over the bed.After a lot of frustration and asking other users in online communities, I settled for diluting the NPA with 1:1 isopropanol in a spray bottle. 2 whiffs of that over the bed, then spread with a microfibre cloth. That works well and lasts many prints!