Bike Rack – Dual Bicycle Stand for Mountain, Road, or Kid’s Bikes – Indoor or Outdoor Steel Bicycle Storage – Tire Rack for Truck by RAD Cycle

Great floor bike rack. Relatively easy to install, instructions are mostly clear, diagrams/pictures could be clearer in a couple areas. One suggestion, which they even mention - only loosely install all the fasteners as you go. This allows some parts to go together since design tolerances of the assembly are pretty tight. AFTER everything is together, then tighten all the screws/fasteners. Some are complaining that this item does not assemble together properly - they did not loosely assemble first, then tighten everything together after everything was assembled. The stand is VERY sturdy. It easily holds my sons two 26in/size medium mountain bikes. I have a 27.5 mountain bike and it holds it too. It looks like it could hole a 29in mountain bike too, but not much of the wheel would be locked in place. You can assemble it to where two bikes are side-by-side, but if you have wider handle bars like most mountain bikes have, the handlebars/grips will pretty much be on top of each other, making removing one of the bikes slightly difficult. That's the only real minor issue I have on this item, otherwise it is great. You can assemble the item to where the two bikes are NOT side-by-side, rather both bikes are in line, but that takes up more space. It has plastic/rubber on the bottom so it does not slip around on the garage floor that much. Overall it is a great value, very well made and sturdy.

As with many of these foreign made products, the assembly directions were unclear and incorrect - total garbage. However, if you have some experience assembling these kinds of things it was fairly easy to figure out. You just need to get the main parts in the correct orientation and my advice is to tighten all screws by hand only and then once you've verified that the entire assembly is put together correctly, you can use the provided hex tool to tighten up all the screws. At first, I thought that the individual components felt a little cheap and flimsy. However, once the entire stand is assembled and all the screws are tightened up, it's rock solid. We use it to store two eMountain Bikes that each weigh over 50 lbs. and it works out perfectly. We simply store one bike with the front wheel in the stand and the other bike with the rear wheel in the stand so that the handlebars are staggered and don't conflict with each other. I am very pleasantly surprised by how effective this stand is for the price point, hence my 5-star review despite the poor assembly directions.

I just received this yesterday and have assembled it so it has not gotten a lot of use yet, but I wanted to note my comments about the assembly while I still remembered. When assembled, the stand seems sturdy and I am happy with it. But the assembly instructions leave much to be desired. I consider myself handy, and had to reassemble a couple of items, so I thought I would give more advice on the assembly here. First in my package, there were no short and long screws, like were mentioned in the instructions. (They are actually bolts not screws.) There were only one length of bolt for the smaller size. I believe that this must have been changed after the instructions were written. The bolts I received worked fine. For steps 1 and 2: When attaching any of the pieces to the larger base rods (B) make sure that the holes in the center of the base rods (B) end up horizontal when the rack is assembled. If not, the left and right side of the base rod (B) needs to flip and then it will. If you do not do this, then the square cross strut (A) will not connect to the rack correctly. For step 2: When inserting the wheel stanchions (C), make sure that the holes halfway up the stanchions are oriented towards the center of the bike rack so that the cross brace (E) can be attached. For step 5: When tightening all of the bolts, tighten all all of the bolts that connect to the base rods (B) first and then place the rack on a level floor and tighten the remaining bolts. I did get a few scratches in the paint where I tightened the bolts. I believe that if you use a socket rather than a wrench, this will not happen. The bolts are all metric. I hope that these additional instructions help. If I had had these extra instructions with the rack, I would have given it 5 stars.

This stands comes with a very simple concept that almost anyone can visually assemble it. So, I did or at least attempted to. Like I said, it's very simple so, it's easy to think, "Who needs instructions?" Turns out that the instructions will help minimize the time needed to put it together and the frustration of having to do it more than once. As others have stated, the sturdiness and quality exceed expectations. The wells are wide apart enough to accommodate 2+ inch tires, as seen in the pictures. Overall, I think it is well worth the price.

I read reviews. I don't always write reviews. I had to this time. I purchased the like "new" product. Obviously someone wasn't able to finish putting it together. There were some scratches. I am a determined woman who loves to put things together. So I took the challenge. I almost gave up. But 1 solid hour later, it's complete. I say this so you know what you're getting into. Most important thing to remember is to barely attach everything because you are going to need to giggle the frame right down to the end to get all the screws in and tight. Also, some other reviews talk about using wrenches. This model came with a tool and that is all I used. The screws are a little different from some videos. See photos. Pros: Rack-Sturdy, heavy duty, solid. Cons: Instructions?🤨 See photos for what mine came with. But it was enough to figure out where things go. Took me a full hour including mistakes. But, assembling it only has to be done once! 🙆🏻‍♀️

Absolutely terrible build quality. You can tell this was designed in CAD, and a prototype was never created, it just went straight to market. Thus no body realized that it physically cannot be assembled without torquing and bending the tubes. It is a nightmare to build even if you have matching sockets and power tools. Just watch the promo video with the AI voice-over in the product images section. you can see that they can't ever get it to sit flat on the floor, and it rocks side to side. after completing. It can be put together if you try hard enough and swear a few times.

Good solid 2 bike rack. Not sure why some people are having issues putting it together. Instructions are very straightforward and literally took me 6.5 minutes to put together. Pro tip= don’t tighten all the bolts until everything is put together. My large MTB tires fit perfectly.

Works perfectly for 2 trek verve 3 bikes, no issues with disc brakes or 700X45 tires. Very stable. As mentioned in several other posts, the holes in one of the main tubes are not even close to being correct. I had to drill them out . No problem but I would like to know who if anyone, inspected them.

Excellent quality durable plastic perfect for Bmx racers without the price tag! It’s Pretty much a box bike stand without the brand logo and price :)

Practical and worth buying

Bolts did not connect to frame, faulty, had to send back

Easy to assemble and does the job well

Great and very affordable bike rack compared to the competition. This is a buy it for life kind of item since it is very sturdy and well built, and I don't see it needing to be replaced for many years to come. Fits mountain and hybrid bike wheels, both front and back. Not much else to say, if you're in the market for a ground bike rack, look no further. Would recommend to anyone.