TossBrightz LED Cornhole Lights (Set of Two) - Weather Resistant Kit

Works great! After looking at other reviews with pictures, the red lights seemed brightest so thats what I bought. Very satisfied. Took ten minutes per board to install with care and followed the directions exactly. I cut the excess hosing off and connected it to the back side of the starting point... good forward thinking on their part to have the connector built in...The pictures capture a lot more light than there actually is but they work great! Can't really see the bags but at least we know where to throw em.

Cool

The installation was very simple and worth it at a discounted price, however, the mounting bracket for the battery pack was very brittle and snapped when trying to attach battery pack. Problems aside, i would recommend this product, great addition to any cornhole board

Lights looks great

There could be A LOT more bulbs, like double the amount, in the strings, and the allotted lights for the board holes was 1/2 the length needed for our standard boards. They lit up the boards slightly more than half of the advertised amount, which led us to believe the boards would be LIT UP brightly, so that was a bummer. Also, the instructions were completely inadequate & it took two people an hour and 15 mins. to attach them, mostly because the screws & nails were the tiniest ever seen & instructions were super vague/non-existent in many ways. We had to figure out placement by looking at the box. (I know... it's NOT ROCKET SCIENCE, but STILL, when you have 3 bags of different fasteners it's good to know what goes where, as well as providing install tips, tricks and placement help...or just Lego Label the bags!) Anyway, for some reason that is entirely unexplainable, the tiny screws that were used to attach the short string around the ring were swapped out with even tinier nails for the longer 4-edge lighting, so get a small Phillips head & even smaller hammer ready...and 6 AA Batteries as well...OH, and 2 florescent stickers, pencil eraser sized. Trust me! Keep on reading...I will get to explaining. If you do buy these lights, here are some instructions help both the Rocket & Non-Rocket Scientists. Promised explanation stars, NOW: Start by flipping the boards over & inserting 3 AA batteries into the black boxes attached to the light strings. Close the boxes & attach them to the boards with the black metal rectangles that come in their own bag, and which were not explained in the instructions, using a Philips head screwdriver. We installed the boxes halfway between the hole & side of the board/towards the foot that props up the top of the board. There is enough wire to do so & this will keep the box both accessible & safe from getting bumped around/knocked off. It also kept the wires out of the way of the collapsible feet on our boards. Next, TURN ON THE LIGHTS with the round, black button on the battery box (near top left corner which you WILL want to remember when it's dark out & are trying to find a black-on-black, flush, pencil eraser sized button or if you are classically aged like me...OR, remember the florescent stickers? This is where they go. Put a bright florescent sticker on each of the battery pack buttons & save yourself the feel around! Now, take a minute to fully unwrap the lights and pull them straight, working out kinks & getting the rubber slightly maliable; slightly being the best you can hope for. While still on the BACK of the board, run the short strand of lights (attached to the box/long lights) around the top half of the hole, as close to the inside edge of the hole as possible without blocking the it. Use the white fastners (3 provided per board), itty bitty screws, and handy dandy Phillips Head. TIP: Tiny screws are squirrelly, squirmy buggers! To get them started & avoid the slips, hold the screw between 2 fingers, tap the screw head (top) a couple times with the handle of the screwdriver which helps get the screw seated, then flip the screwdriver to the business end and finish screwing the screw in. Next, flip over the board to the FRONT side to be sure the lights can be seen & hole is clear. Adjust as necessary, which allows you more quality time with those wee screws. (We chose to use the "half-needed amount of lights" around the top of the hole to avoid backlighting the hole into shadow...again, not in instructions.) Moving onto the long strand & (odd) change to fastners with nails...lay the board on it's side and start attaching lights to the thin side wall of the board...NOT the top (this will interfere with game play & lead to loads of lands that clearly should have shuffled off the top of the board's buffalo) OR underneath the board (lights won't be seen, but the ground will surely look cool). You will space fastners out to have 4-5 per long side & 2-3 per short side. (Good news! Ample fasteners are included!) Start at one end, attach a fastner, go to the opposite end, attach a fastner, find the halfway point, attach a fastner, then install 2 more fastners between the middle and each corner on the same side. Definitely don't try attaching 1 corner and working consecutively along to the opposite corner. The rubber is pretty stiff and wants to roll off when you first start a side, so the "end-end-middle-in between" technique WILL save you time. Also, start at the corner nearest the battery pack, flipping the board on it's long side or short end as you go. The corners will want to roll on top of under the board. This is where the stretching out from earlier comes into play. When going around a corner, your now kink-free, malleable wire will allow you to pull it TAUGHTLY around, placing the 1st fastner of the new side immediately. This is a great time to get those extra hands or a clip to hold the wire down snuggly, allowing you to master the wee nail. Continue around adding fasters and wee nails until you are back to the start again. We ended up with an extra 3" of wire at the end (not enough to reach/finish the hole), so we just used some paper tape (out of our wee friends & fasters) to adhere the extra length under the board & enjoyed the green night grass. And that's that...All that remains is to set up your boards outside, when its getting dark, press the now easily located irridescent button AND...prepare to be underwhelmed. Happy Holing, one and all!

Very well built & worth the little extra money! Will last a long time !

The make the boards stand out and takes the game into overtime without spotlights. That's about all the good things I can say about these. My reccomendation is dont buy these. Where do I start? From a design standpoint these are terrible. The adhesive for velcro patches doesn't stick to back of boards. I had to use auto grade 2sided tape to hold them to the boards. The next problem is the battery case itself. Instead of placing the weight of the batteries on the back piece it's on the front closure part which simply clicks in place..AWFUL!! Every time a bag hits the board the battery pack is knocked off and hits the ground. If that's not enough the gauge wire is so thin and short that as the pack continuously falls it eventually snaps the thin wire. Now only my lights around the hole light but the battery pack still doesnt stay in place. This is a flawed design and not worth the waste of money. My 12 year old nephew was able to trouble shoot and offer much better design to make these functional. That should about sum up what you need to kno to not purchase this product. I would give this no stars if I could.

Love these! We thought we’d need glow in the dark bags, too, but these glow brightly enough that the whole board is lit up. Sized perfectly to go around the board and the hole, plus installation was a breeze. Worth it for the price!

Las luces para el agujero son cortas, para un agujero estándar de 15 cm de diámetro, le faltan 3 luces o 12 cm más de luces.

Circle light string is not long enough to go around the board hole. Controller arrived broken with power button snapped off and lid clip cracked off.