TP-Link TL-WA1201, AC1200 Dual Band Wireless Gigabit Access Point

Very easy to setup, seems to work flawlessly. Used for a TV to bypass the wifi.

This piece is the BOMB !! TP-Link TL-WA-1201 I had let two different 'range extender' pieces drive me nuts, their software was hard to use, but once figured out it still didn't work, signal was lame and choppy. So drilled into web and learned superiority of Access Point. Thought I'd try a base monel to learn on. Trust me, TP-Link really knows what they're doing. Instructions were clear, everything I was sent to look for was there, the steps made sense, their website fed back reliably, and within a couple hours IT WORKED! And it waxs LOUD! Signal next to it 76%, outdoors 30-ft from unit is still 65%. Amazing, Software is brilliant, now that I did one, doing the next will take about ten minutes, it's a breeze to work with. BUY THIS, even if you don't need it. Yet. You will, it's a spoiler.

This little beast supports four modes out of the box: Access Point Mode – turn wired into wireless ✔️ Range Extender Mode – repeat an existing signal ✔️ Client Mode – convert Ethernet-only devices (like a printer or old PC) into Wi-Fi clients ✔️ Multi-SSID Mode – create segmented guest networks with VLANs ✔️ I ran this in both Access Point and Extender modes in a tricky layout (concrete walls, multi-floor), and it pushed out clean dual-band signal without any noticeable lag or packet loss. Plus, MU-MIMO and beamforming help direct the signal where it matters—great for multi-device households or streaming-heavy setups. What I Like: Dual-band speeds (867 Mbps on 5GHz + 300 Mbps on 2.4GHz)—solid for most streaming and gaming Gigabit Ethernet port = no bottleneck on backhaul or client mode Passive PoE support—clean mounting, especially if you're running it up a wall or ceiling Four fixed antennas deliver real coverage, not just marketing fluff Pro Tips: Pair with a modern router for max benefit—don't bottleneck this thing with an old base station Use a dedicated SSID in AP mode for clean handoff between routers In Range Extender mode, place it midway between router and dead zone for best balance of signal vs. speed What Could Be Better: Web interface is solid but not quite as slick as newer TP-Link Omada gear Fixed antennas = solid signal but less customization of direction No mesh functionality—if you want seamless handoff, go Deco instead TL;DR: The TP-Link TL-WA1201 is a super versatile, cost-effective, and stable Wi-Fi extender/access point. Whether you’re bridging old gear, extending signal to a dead zone, or segmenting networks with VLANs—it handles it all quietly and efficiently. No dropped Zoom calls. No gaming lag. Just clean, customizable Wi-Fi wherever you need it.

I'm using this as a true access point. There are actually 4 different modes this unit can be used in. As a range extender, it gathers and repeats your wifi network to cover dead spots in your home. Used in client mode, it's antennae capture signals from your wifi and allow you to run a connected device via ethernet port. In multi-SSID mode create multiple SSIDs an VLANs, useful if you have devices you want to be able to communicate together, but separate from other devices on different VLANs (which wouldn't see each other from a connectivity standpoint). I had hoped to use it as an access point and connect it to my primary router via CAT6 cable that runs from one end of the house to the other. From there, I set up a different SSID from my primary router so that I could run a small office wirelessly. I have a 1 GB fiber connection as my main internet source. Speedtest rates it as 950mb- 1GB both upload and download. The ehternet connection to my router brings the full 1 GB back to the access point over hard wire, but testing the wifi from this access point only gives about 50mb up/down on Speedtest.net. Fortunately, 50 mb per device is sufficient for everything I do (video calls, internet browsing, access to web based apps like Teams), but I had hoped for better wifi speed. Easy to install and setup, the directions are very good. The price is very attractive, and you can use it in multiple modes. Of course, I may be an extreme case. If you are only getting 50mb from your primary internet connection, this works great.

TL;dr -- this AP is another case of good hardware, awful firmware. The OEM firmware makes this device unusable, but flashing OpenWRT makes it useful again. Full Review: I bought this access point to use as a wireless client bridge for a computer in my house that gets an extremely poor wireless signal. Initially, I was disappointed because I was limited to a 2.4GHz connection, as the 5GHz connection was too unstable to be used. I'd regularly run into issues watching YouTube videos, browsing the web, or making Zoom calls. The solution was to use the 2.4GHz radio instead. This meant that my connection was limited to ~45-60mbps, which pales in comparison to a typical 5GHz connection speed of ~250-300mbps. For reference, my iPhone 11 is able to pull ~560-620mbps when placed next to the hardwired access point. i initially considered returning the AP, but then I found someone online had ported OpenWRT to this access point. Although this may void the warranty, it solved my issue. No longer do I have stability issues with the 5GHz radio, which means that I have both a reliable and fast connection to the Internet again my home office. OpenWRT is great, although it's far more complicated of an interface than the default TP-Link one. I would not recommend using this device in this configuration unless you're familiar with more advanced networking concepts or are willing to learn. Pros: - Inexpensive - Supports wireless client bridge mode. - Supports PoE using the provided injector. This is extremely beneficial to my setup, since I can place the AP where I best receive a signal, even though I don't have a power outlet nearby. - The Qualcomm Atheros QCA9886 802.11acn wireless radio has excellent performance - Gigabit LAN port (to the reviewer claiming it doesn't have one, this is simply not the case; there's no way I'd be able to pull 300mbps if it had a 10/100 interface). - The default firmware supports bridge mode with DHCP & NAT disabled, which means that every device connected through this AP has its real Ethernet MAC address exposed. If you plan to use this on a college campus or want your connected device(s) to be bridged to the parent network, this is very useful. If you use this mode, you can still control the AP's settings using the assign IP address for the access point itself. Cons: - Default firmware means that the 5GHz radio is unstable. I also had problems with controlling the LEDs and updating settings. Bonus Pro-tip: I only used this device with one computer, but you could easily use an Ethernet switch with the single port on the back of this device to connect multiple computers/devices.

I bought the TP‑Link AC1200 Access Point to get more reliable WiFi in my office, which is the furthest point from our main router. Setup was the easiest of any WiFi device I’ve owned — up and running in minutes with zero hassle. I’m using it as an extender, and the connection is now solid and consistent where it used to drop constantly. Exactly what I needed, and it works better than expected.

Seems to work well. No complaints

I set up this using the QR code provided. I was directed to a screen to enter my email and name. Once there, the next screen wanted a credit card number. I felt that was odd but I entered my CC number and within 30 seconds, I received a fraudulent charge alert from my bank for $39.99 at a website I've never visited. This product has been hacked or something else is wrong. I'm returning it as I'm now without my CC for a week until a new one is issued. Total BS!

Werkt heel goed

I like this Access Point, it looks like a little alien space ship on top of my DVD tower. I have installed 3x APs in the past and a couple of them were very frustrating to setup. The most annoying requirement was to use an unusual I/P address e.g. 192.168.2.2 This requires re configuring your laptop/PC to match this unusual I/P. With this AP there are no such horrors, you can access the setup page from a PC using Ethernet or WiFi using a laptop or smart phone. it uses the addressing format used by most homes i.e. 192.168.0.XXX The ID and password are on the bottom of the device. Mine I/P was 192.168.0.160 Change these to suit but make sure you write the new details down. You need 2x sets of passwords 1. A user name and password to get back into the setup page. 2. An SSID and a password to enable encryption. The setup menu was very easy to use and worked without any issues. As well as SSID and password you can also select the channel to use for WiFi to avoid conflict with the router WiFi 2.4Ghz and 5Ghz can be separated and given unique SSIDs if necessary. There is also an option for a "Guest SSID" If you do forget the new passwords, reset with the button on the back and start again. Once set up connect the AP to the router via Ethernet cable and you are ready to go. The listing says that the AP supports passive PoE which I've never used and wasn't too worried about. I was pleasantly surprised to find that a tiny PoE injector was included. An Ethernet cable contains 8 wires forming 4x sets of twisted pairs. These are used to send and receive data simultaneously but not all of them are used. PoE sends power to the AP along 2 of the unused wires. This gives you 2 options. Plug the supplied PSU into the AP, the usual method. Plug the PSU into the small PoE adapter. Plug the Ethernet to Router cable into the socket marked "LAN" (Local Area Network) Then plug an Ethernet cable into the adapter socket marked PoE, the other end going into the AP. This made it very easy to mount my AP in the sky on top of a DVD tower with just one Ethernet cable. The supplied PSU lead was not long enough to reach that far. Very pleased with this Access Point 11/7/26 Update I use Powerline adapters to connect to this AP and out to my shed where another wireless AP manages 6-8 IP cameras. I also had temporarily 4 cameras connecting to this AP. I started to "loose" a camera but only when I was using my phone. Google search came up with some suggested changes to the AP settings. I did some changes to the AP settings as suggested by the AI. I normally access APs using my PC. After making some changes I was suddenly unable to access the AP anymore and left it for another day. A day or so later I realised that my phone had stopped connecting to the AP but rather oddly some cameras were still worked fine. I could not connect to the AP via ethernet using a PC, I tried 2 of them. I reset the AP 2 or 3 times no response. I then tried to connect using WiFi and it connected. What seems to have happened is the AP had got locked up mid change to the settings. I had an "allow items" list that contained a few things like my cameras but not the phone. The IP had been reset to none. I made the necessary changes to settings and now all works as it should. Very strange that the Reset button did not work. If you find yourself locked out via PC and Ethernet, try accessing by Wifi It uses the SSID to connect so no IP is not a problem to the AP.

Excellent item delivered very quickly. Very easy to set up.

Good Quality!

very nice product i used it as a range extender to boost my wifi signal working very good