5 Pieces 3 Meters K Type Mini-Connector Thermocouple Temperature Probe Sensor K Type Thermocouple Wire Temperature Sensing Line Measure Range -50 to 400 Celsius, Compatible with TM902C/ TES1310

I bought these because one of my multimeters has a temperature measurement function and uses K-type thermocouples with this type of plug. I only had one thermocouple for it and, though I rarely use it, I don't like the idea of being without it if the thermocouple breaks. Sometimes an infrared thermometer just isn't good enough and you need to stick an actual thermocouple onto what you're measuring. I received the set of 5 and plugged them in. All of them seemed to read the ambient temperature in my garage (65ish degrees F) correctly. All of them heated up to 80-something degrees between my fingertips. That was the extent of measuring that I did so I can't vouch for their accuracy. A better way to do this is to measure boiling water (212F at sea level) and ice (0F). These two data points should tell you if things are relatively close, or at least if something is drastically wrong. For bonus points, you can measure the temperature of other cooling baths to get more data. Something like acetone and dry ice (-108F) or liquid out of an air duster can (roughly -4F to -12F for difluoroethane) will give you some interesting data points. Someday I might do that. Not too long ago I'd probably have been buying these things from Omega Engineering or someplace similar. The quality would have been good but I would've paid more for one thermocouple from them than I paid for all five of these. For non-critical measurements, having inexpensive ones like this around is fantastic.

If you've worked with these kinds of sensors at all you know they are fragile as heck. I had one that came with an expensive multimeter fail out of the box. I bought these to verify the problem was the probe and not the meter itself. Plugged it in and got nearly instant readings. Temp readings were accurate. By buying this bulk pack now I have some in reserve for when another one breaks. Side note - How these devices work is by using two dissimilar metal wires which are soldered or bonded together at the probe end. When the dissimilar metals are exposed to changing temperatures they create an electrical reaction which a meter can measure. The wires are tiny, and if exposed to a lot of mechanical stress they will separate electrically (i.e. break) which causes the probe to fail or become unreliable. Just FYI.

They functioned for what it's needed but not without issue. I was really hoping they had a more weighted end so it would stay in place to monitor my oven temp accuracy. Thats the only reason for 4 stars. They both measured fairly close in temp which i know isn't expected. After using i threw them out because wire that thin will suffer reliability issues after 30-40 mins in 350⁰ heat

I use these for measuring everything from heated floors and HVAC systems to 3D printer bed temperatures with my Agilent and Siglent DMMs. I have not had any issue with the probes. They seem accurate (as accurate as any K-type thermocouple) and are well made. With the 5 supplied, these should last me for many, many years.

These are amazing and an absolute time saver. They provide very accurate readings compared to other temperature probes out there. I used them for my heat pumps class and attached them to the refrigerant lines for taking temperatures. Just tape them on and ready to go. They ends are very delicate though so just be careful when handling them.

Some of these had reversed polarity. They only had to solder 2 wires and they couldn't get it right. Oh well, what else should I have expected?

Wires are extremely thin: single strand 30 AWG or ~0.25mm. Prob OK for a static run, but I would avoid if the cable has to move much. They are cheap so you can always throw out a broken one and use a new one if it's in a easy place to get to. Also If you are planning on using on a amplifier breakout with wire block connector, these wires will likely be too thin.

We have a very old TC welding machine that we used to make Thermo Couples. It works well and is very handy. I purchased these TCs as a test to see if we could use purchased TCs, if our welder failed. The purchased TCs from this vendor are equal in every way to those we make. I compared the temperature reading with a quality Fluke, handheld meter. The TCs we make (that I trust) read identical to those from the vendor. The only question might be the quality of the insulation. I say “question” because I have not tested the resistance to burning of their fiberglass insulation but it appears to be authentic fiberglass sheathing. I will test heat resistance and update this post.

Accurate, cheap. They work perfectly!

When compared to the one that came with my test equipment these measure very close to same temp I was getting from the original one.