TotalBoat TotalProtect Marine Barrier Coat Epoxy Primer - White Quart

Love total boat products have used this epoxy on multiple boat restorations is tough as nails, works well with their other products of course follow the instructions on the website and you’ll get a great easy to use product, this product is durable, a great value for the money, but remember poor surface prep no matter the product will always give poor results

Using this epoxy primer to paint the roof of my school bus. I wanted a great primer for the bus roof and will use the same brand when purchasing the same brand topcoat. Cost more but buy once and cry once so I do not have to do this again. Marine paint is UV resistant.

Used it as a primer coat for Interlux BilgeKote in the bilge of a boat while engine and outdrive was removed for rebuilding. All application surfaces were cleaned and degreased. The surfaces over which this was applied was a mix of epoxy, JB Weld, and gel coat. Areas were painted with a 4" foam roller and a 2" disposable brush. The foam roller purchased from the local home-doodle store started to crack and get limp right around the time I finished (1/2 hour later) apparently due to the chemicals in the primer attacking the foam. Primer adhered quite well to all surfaces, even the smooth areas of the gel coat which was not scuffed. This stuff just plain sticks! One quart was ample with about 6 ounces to spare for any touch-up. Epoxy mixed well with drill and mixing tool. Clean up with Xylene was painless. I have yet to apply the BilgeKote, but looking at the instructions, I expect no issues.

I decided to use this to seal up the bottom of my 15' whaler Ive been restoring for below the waterline. The prior owner had old paint that was peeling. Sanded it all off and put 3 coats of this one with a foam roller from Lowes. I tried with a 4" quality nap, but it started to shed. The foam rollers seemed to do a great job and went on fairly well. But when it dried, it left it a little rough. I went to sand it smooth to prep for bottom paint it was a bear to sand. I thought I could knock it down with 320, no luck.. tried 220, no luck.. finally went to 80 (all I had around) and it started to come off, but clogged a ton.. then came back to 320 to smooth it off better. Being that it will be below the waterline, Im not overly concerned, but not being able to smooth it out easily either at application or sanding later is somewhat disappointing. I was expecting for it smooth out easily but my guess its this epoxy is really strong which is great, but tough to work with it. Working time I had no problems. It mixed fine 3:1. Gas off for 15 minutes and rolled on. It does have a pot life about 4 hours or so. I was apply to keep going coat after coat.. Fumes were not bad, have had worse.

I used this paint on a marine-plywood rowing boat. As an epoxy, it bonds well with wood and with scuffed coast of epoxy. This is my below-the-waterline barrier coat and I'm also using it on the interior planks of the dinghy as a waterproof primer. This paint is the consistency of mayonnaise with not much liquid in the container. You'll want an electric drill-powered paint mixer to thoroughly mix the paint and the catalyst. It rolls on thick and easy and doesn't sag but the finish is not smooth like topside paint. Use as-is to protect fiberglass boat hulls. I'll leave it as-is below the waterline but am using two coats so I can sand it smooth and fill with a primer above the waterline before applying topside paint. Also, the directions say to let the paint sit after mixing. Pot life is long so no need to hurry like you would with 5:1 epoxy.

Great primer for boat hulls, etc Dries to a tough film overnight yet still easy to sand. Says you can’t apply over a 1 part paint, but I used it over dry, sanded Kilz 3 and it was fine. First gallon I purchased from Amazon. I found out the hard way Amazon paint products are not returnable so I looked around. Thats when I found Jamestown Distributors. Same pricing and delivery timing, but included a paint suit, stir stick, roller & pan, roll of tape, and tack cloth, plus’s 10% discount. Not sure of their return policy, but it can’t be worse and the rest is better. Even shipping. Amazons stuff was all dented, Jamestown’s arrived in perfect condition.

I own a 12' fiberglass boat. One quart ,thinned out properly using Thinner 200, was able to coat the entire inside of the boat twice. So I was able to achieve the recommended coats of 4-5 by using two quarts. I applied with a 9 inch roller with a 3/16" nap. (I didn't tip and roll) All supplies were made by Wooster. Be sure to follow instructions carefully. One side note is to buy a mixer attachment for a drill. The base (paint) is very thick and needs to be mixed thoroughly before mixing with the hardener. Stir for 2 min. Induce 15min ,thin and apply. I have 0 complaints, and will buy again for the next time I need to paint my boat. It's important your roller nap is 3/16" for this two part Primer. Mix the proper amounts and it should go smooth like my experience. Good luck folks. Don't cut corners and get yourself some Wooster supplies .

Great product