Danco 10086 VersaSpray Portable Hand Held Shower Head Sprayer Fits Bathtubs Without Diverter, 1 Pack, White

Excellent stand in shower head. Fitted the tap OK but used a couple of cable ties to make sure it didn’t blow off under pressure.

Does work, water gushes out of the seal.

Fitted well on a square tap.

The good bit is that it does the job, I would say the quality for the money is very poor, it’s constructed with very poor quality plastics. We bought it as a temporary measure as our main bathroom is getting refurbished, this will do fine as a short term solution but I certainly wouldn’t like to rely on it for any period of time.

Worked great for my needs - having moved house and discovered the bath shower tap diverter is seized and being unable to get it working. The taps are not possible to replace without removing the bath due to unusual layout and this product has allowed me to set up a temporary shower until my renovations. The end fits well on my wide, flat spout and the metal ring tightens well, though I have used plumbers tape to help ensure a tight seal. The only issue I had was the shower head does not fit into the existing holder. I've got around this with some padding material and more tape but it would be much better if the shower head had a standard fitting to allow it to slot into most shower holders for anyone else needing to use this as a temporary shower solution.

A fair price for a very good quality product, great service provider. Highly recommend, will definitely use these guys again ⭐⭐⭐⭐⭐

Not very good for my taps. If I open the taps to much it leaks.

the plastic hose is not very supple and therefor kinks when trying to unwind , very cheap for the price

Material de la mejor calidad. Ayuda para lavar el cabello.

Fab shower head, has worked far better than I thought it would! My advice to anyone buying is that it will work if you have a compatible tap but it does take some trial and error to get it right but when you figure it out it's very good and will work a treat.As it didn't come with any instructions I cracked on and tried to fit it with alot of leaking. When I looked at the company website they advise soaking the shower head on hot water for 5 minutes before fitting, this is very helpful as it softens the rubber and makes it easier to fit. You also might not be able to just shove it on the tap and tighten the clip. Take some time to tighten it fully then turn the water on slowly and check for leaks, I fit mine almost at the end of the spout and it gets a perfect seal.So push it on fully, tighten, test and if its leaking just loosen and pull it towards the end of the spout and repeat. You really just need to have patience and play with it until you find the spot that works on the tap. But most importantly SOAK IN HOT WATER FOR 5 MINUTES BEFORE FITTING TO THE TAP!!!

I have to say that it's changed our household and solved a very big problem of having one shower and one bathtub and two people who both like showers and separate bathrooms. The key is the installation, and it may take a few times to secure it just right. Trust me, you will have a few "Jerry Lewis" moments with water spouting all over the place, but once it's installed right, it works great. The key is to use an adjustable O-clamp (they're like two bucks at hardware stores) and secure the clamp over the part that goes over the tub faucet. Use a flat head screw driver and tighten the heck out of the clamp--I mean really screw it on tight. My place was built in the early 1980's and has a typical square opening faucet. It was tough to get it to fit but if you move it side to side and apply pressure, it eventually fits over the spout. Sit in the tub when you do this, not from the side. If you need the shower head to secure to the shower wall, for about 12 bucks you can buy a fixture that sticks on just about any surface and holds the nozzle in place. Once you get that nozzle positioned in the right direction, don't ever touch it again; leave well enough alone or it will fall off. Also, if your home has high water pressure (the kind that takes your freckles off), turn the shower on slowly instead of just cranking it on full power at first. If you can do this, you will convert your tub into a great shower for under 30 bucks! If the manufacturer is reading this, the instructions are bleak at best and should add installation tips so people won't toss this simple but true device and complain that they "were had." It's a great product but it needs a little TLC.

This product made my life easier, I use it to give bath to my baby. Not sure why there are too many 1 star ratings, I'm just glad I took a chance on this one. Also to note, this product wont work for spout that has a diverter, its only meant for the ones that doesn't have the diverter which perfectly suits for my bath tub. Very easy to install, just soak it in hot water for 10 mins and then attach it to the spout!

I followed the instructions to use hot water to make the attachment "softer" but still won't fit onto a regular size bath tub faucet. Totally useless. Do Not Buy.