EZARC 3pcs Oscillating Tool Blades Carbide Multitool Saw Blades for Hard Material, Hardened Metal, Nails, Bolts and Screws, 3-Pack

The best multi-tool blades for cutting metal bar none. I do not know how they do it, but these blades are amazing; massively better then any others I have used. I am repairing an old house & have to cut lots of old nails, screws & other metal fixings so as not to damage the wood/stone they are attached to: I went through blade after blade, trying all the big names but none would cut more than a few iron nails. These babies, however, cut through them like butter. I came across them on a USA video review of multi-tool blades, which they won easily. I was a tad sceptical (maybe the reviewer works for EZARC) but, when they arrived, I was very surprised at how brilliant they actually are at cutting iron, steel & even stainless steel. I should not gush about a simple blade, but they are that good. I do not know how they are so much better than the competition; but they really are. Do not hesitate; buy them.

These are the only blades that will cut though my summer house . So glad I got these . Other blades I tried were blunt in seconds

A set of cheap cutters that can be used on hardened screw and bolts. This has cut through 6, 4mm screws quickly and without issue. There appears to be an edge on the blade still. Use with a slow spread, allowing the edge to cool by removing pressure occasionally.

I did not stumble on these. They were a choice made after extensive reading up on what I needed to cut through some stubborn hardened nails. I was trying to remove the vertical frame of a garden fence panel that was nailed to the main posts - and to do so carefully as I needed to repair a section of it and put it back. I tried prising with all sorts of tools and angles to try and get enough purchase with a claw hammer so I could pull the nails out - no joy! Any harder and I was simply going to split the wood. The nails didn't budge at all. I decided to bring out the big guns in the form of my Milwaukee Cordless 18V oscillating Multi-tool with a view to simply cut through the nails through the joint between the frame and the post. I fitted my Smart brand plunge cutting blade for metal and went for it. In no time at all, the blade was completely blunted and the nail was still intact with little more than a scratch. I was very confident my Oscillating Multi-tool was more than capable so focus was on the blade. I did some online reading and quickly came to the conclusion I needed some Carbide tipped blades for hardened nails. Further review of comparisons of various blades on Youtube convinced me EZARC was the way to go here and the 3 pack pricing made this decision a no brainer. Availability on Prime was simply the icing on the cake. And so the moment of truth. I got my blades on the due date but somewhat late afternoon/early evening so out of regard for my neighbours postponed my rematch with the fence until the next day. Judgment day, and out came the Multi-tool once more, new blade fitted, and I stepped outside to face my foe. We are talking roughly 6 seconds to cut through the first nail - and that was me being cautious, expecting the same blunting I saw with my Smart brand blades. It was same again for the second and the third nail. I checked the blade after each on of these cuts and it was as if I hadn't done anything! No blunting observed! I turned to the other post and was done in a matter of seconds. Within 5 minutes of my stepping out the door, I had the fence panel flat on the ground ready for the repair work to begin. I was so very impressed with these blades that I decided to share this review on Amazon pretty much straight away! Indeed, I am only part way through the repairs as I write but that is for other reasons. Summary? Sure: Pros: Sharp, heavy duty, cut through hardened nails easily, well priced, well reviewed brand Cons: None Verdict: If these sound like what you are looking for, they probably ARE what you are looking for. No regrets to be had here; you're onto a winner! A+++

Definitely thought twice about the cost of these but after the bolts I were cutting melted my DIY shop bought blades took the plunge ... Good Decision

Got through two bladed cutting through four drop lin bolts on the car. A lot easier than using a hacksaw for sure, and worked fairly well. But ripped a lot of teeth off and had to throw them away when the job was done.

These are far more durable than any 'wood/metal' cutting blades available in builders merchants / Screwfix etc. It's quite a fine tooth so set speed to medium, find the pressure 'sweet spot' and it'll cut faster and last longer than whacking it on full speed which just generates lots of heat. I've cut dozens of nails and a few10mm coach bolts with one blade while dismantling an old stable and it's still going strong.

These blades cut okay but don’t last too long if cutting things like hardened screws. I thought that 3 blades for the price was good value and they do do what they are intended for

The first blade I used cut through copper pipe quite well but after third pipe it separated at the spot welds. Quite disappointed considering the price and expectations.

muy buenas. me estan durando mucho. Mejores que las de la marca dwalt que compre antes y mas baratas

Habe mit einem bereits 4x 1/2" Stahl-Heizungsrohre abgeschnitten, schneidet immernoch sehr gut. Die sind qualitativ echt top!

Used it to cut some stainless steel piping, and it managed to get the job done efficiently without killing the teeth, which was a problem for bi-metal blades

Tres bon résistance mais un peu cher