BINZET AC to DC 12V 10A 120W Power Supply Adapter Converter Regulator, 5.5mm x 2.1mm DC Plug, 12Volt 10Amp Wall Power Plug for DC12V 5050 5630 Flexible LED Strip Lights

We got the Power Supply Adapter Converter Regulator to use on our OGO toilet and are very satisfied with its performance. As a plug-in unit, we needed a 5.5mm x 2.1mm size plug and had ordered a different connection but had to send it back since it was off by a millimeter. Ordered this one, it plugged in easily, and works very well - it's connected 24/7 and has never faltered. Very happy with the quality and durability of the adapter.

So far they have been very reliable and live up to their claims. I'm using them with digital guitar amplifiers That have PWM converters in them for power. (12vdc to 60vdc) They are nice clean well constructed units. I'm surprised that they didn't cost more. Would I purchase again? You bet.

great product. well made works great

Bought this to power my telescope, camera, and mount. It works fine and I haven't had any problems, but you can tell it's not the most robust and since my gear is worth thousands, I sprung for a Pegasus Astro power supply, which should be made to more exacting standards. But for a cheap 10a power supply, this has worked great for a couple of years.

Did what I needed it to do!

bought this to power a pump intended for direct wire, so I knew I would be snipping it's tip it seems ok, but there is an issue with surge current, the pump is supposedly only 30w but without a supercap block the pump doesn't run as nicely this PSU is ok though since it does self-reset after a few seconds after an overload so connecting a supercap to buffer a spikey load works to be clear this is a 10a PSU, 30w is less than 3a, so even if surge is 3x the normal load this PSU should not struggle

It worked fine for 3 months -- no problems at all. Then it died, showing a flashing indicator. At this point, the max load it could drive was about 2W (one LED bulb, 0.1A). I also got a wickedly large spark from the electrical outlet when plugging it back in. I left it unplugged for a while to see it if might reset itself, but no luck. No sign of damage, and no incidents likely to damage it (power outages, surges, short-circuits etc). It was used to drive a load of about 30W (3A) for 8 hours per day. It doesn't seem it was up to that task.

Great little converter to power an led array. My previous one zonked out at about 6 months which was very disappointing. This one feels like it's made a little better. When I first turned it on there was a 3-5 second delay in powering the led's which, I'm assuming, was a capacitor charging. It was a little un-nerving as I thought, Oh No, freakin thing is dead!! But after said delay, the led's lit up under my counters and the delays are gone now. I like the thought of a capacitor buffering and protecting the transformer circuitry (if that's how it's designed) from the constant on-off cycles. My led's are hooked into a z-wave switch controlled by an Alexa. So, on-off cycles are a constant throughout the day being that Alexa makes it super easy. This one has also been running significantly cooler than my previous one leading me to believe it's not working as hard. And, this one matched the power specs to my old one! I've learned cooler is always better where circuitry is concerned. Longevity? We'll see. So far so good for now though.

Product was exactly what I ordered worked perfectly had an issue with shipping that I believe was probably my fault but they sorted it out for me and got it to me rather quickly, extremely happy with everything,

Powers up my 12v gadget, tested it at 40watts with no issues, haven't tried the rated 60w, some comments mentioned noise, mine is very quiet. **Update: It failed after only 5 months of use, I do not recommend this product.

The 110v power cable shown in the images is not what comes with this power supply. Comes with a thin cable that after using outside in moderately cold weather snapped in multiple places. Probably ok for indoor use, where its connected and never removed.