upHere GS05ARGB Addressable RGB Graphics Card GPU Brace Support Video Card Sag Holder/Holster Bracket,Built-in ARGB Strip,Adjustable Length and Height Support

For $15 you can't get much better than this. Most GPU support brackets are crazy expensive. This one is pure quality for only $15. It is made of solid metal, so you don't have to worry about it not doing it's job. The RGB syncs to you motherboard, and the colors match. RGB is subtle and not obnoxious, only issue I can see is the adjustment for the amount of support doesn't really help all that much, and you're stuck guessing at how high you need it, but once it's set you're good. Sag is gone and it's a really good looking piece in any build. The only bad part is putting in the screws for the expansion slots, a magnetic long screwdriver is a must, otherwise you'll spend a lot of time trying to set the screws and then trying to screw them in.

I say less conventional because I did use them as GPU supports for 2 different systems, a job they do well, easy to adjust and 3 point contact for the base BUT I took the RGB strips out and put in some cut-down strips from a set with proprietary connectors with the fan kits iinstalled in those systems. I then to those addressable strips that came with the brackets and put them in a different system as general RGB strips off to the sides. Not only do the custom jobs look great, but the strips were easy to work with and can daisy chain and look great. That's why I did not include pictures, because some people will see something that is NOT what they purchased and probably won't read this and get pissed off haha but they are great supports, great RGB and easy to open up and mod for proprietary setups

Yes it is mainly plastic, yes it will more than likely bend a little once you get it installed. But I ask what would you rather bend. the mount or the expensive video card you are installing it for? I had a bottom RGB plug free and it synced up with my Motherboard no trouble. It is holding up a very large Sapphire Nitro+ 6900xt and does it well. I was able to adjust it where the mount hits the shroud case not the fans. Good product IMO.

I’m very pleased with this GPU support bracket. I installed it in an NZXT H5 Elite build with an MSI RTX 3080, and it adds a clean finishing touch to the lower corner of the case. The RGB lighting looks great through the glass panel, while the bracket provides useful support for a larger, heavier GPU. For around $13, I don't think it could have better value and makes the whole setup look more complete. 5 stars.

The quality here is more than acceptable for the price, but the individual item delivered was plainly not new, and was missing the rubber pads described in other reviews. That wouldn't have been a show stopper, but the Arc 770's lower shroud is curved -- attractive, but not really compatible with the small flat platform on offer at the end of the strut here. In addition, I'm a tad skeptical of the design after an attempt to install -- in theory, the use of three slot screws should be pretty solid. But in practice there's too much play for the thing to be really stable. You really have to bear down on the screws (more than I'm comfortable with anyway), and you also have to get the thumbscrew that holds the card up just right to really prevent sag. In my case, the only place I could find that would allow the system to prop up the card was along the edge of the cut out for the fan -- not really ideal. The RGB plug on my unit was also loose and readily slid off the motherboard header -- but I suspect that was an issue with this particular unit. The lighting itself was fine. Not really a negative review -- what's here is reasonably well made. Just not a design that ended up working in my particular use case. I'm not sure the Intel card is really heavy enough to require a brace. But I may try one of the thin posts that are magnetic on the bottom and threaded on top to allow more precision about the upward pressure applied to the card, and a simpler design that is less likely to allow play. Sometimes simpler is better.

Wonderful product does exactly what it states. works with D_LED headers on your motherboard (I have a Z390 Aorus Master). This can be a bit of a pain to install if you want to keep your PCI-E blanks on behind it in corsair cases since their covers are designed such that they are under a small amount of tension. With a bit of fiddling I managed to keep them in place however. Note that this does block 3 PCI-E slots unless you are installing a low profile device behind it, so make sure you have enough below your GPU. As a small note, mine came slightly bent at the attachment point, but it was nothing that wasn't easy to fix!

For the price this can't be beat. Its simple and easy to install. For those saying they need to bend the bracket to work with an EVGA RTX 3090 FTW3 Ultra Gaming GPU, you do not. As another reviewer pointed out, just move the stand back to the middle of the card. The center fan is offset back from the other two and the stand will fit perfectly in that spot and not interfere with any fan operation. I can only show the rgb working through EVGA Precision X1 software. Since these cards come with a 5v header I just plugged it into that and the color representation has been spot on. Since the bracket does not have a support back to the motherboard (if it did, I would not have bought it) it can be a little wobbly but once you have it set where you want it, it will remain there. Now, if you are one of those people that still lugs their desktop gaming parties then I suggest a little super glue on the rubber pads. As others have stated, these things just fall out. I think in one of my pictures one had already moved out. I reset them and they are remaining in their spot now but I would expect to find them in a fan if I had to move this big case to another room. All in all, easy to install and looks great and at a third the cost of the Cooler Master stand, its a steal, especially if you have fans on the bottom and cannot use a regular post stand.

It's perfect for the money, came with 1 dead LED but it's not a big deal you can't notice it unless you're really staring at it because of the diffuse plate. It's going to work great and keeps some weight off my PCI-e slot when my triple slot GPU is installed. Pros: Thicker than I was expecting, pretty sturdy design. Comes with long thumb screws so you can keep your PCI-e covers on, or install a smaller card behind it(e.g Wifi, NVMe Raid Card) Addressable RGB is great, syncs perfectly. Comes with Rubber pads for vibrations No SATA Power needed(idk what some of these other reviews are talking about) Slider can be adjusted on both an X and Y axis. Nice quality packaging Cheap Cons: Has one dead LED(Not really too noticeable though) RGB is a little less saturated than my RAM and Fans. Slider is a little bit stiff when moving up or over the first time. Sits slightly crooked with weight on it, like 2 degrees not a big deal, barely noticeable.

Me encanto, queda muy bien en mi ensamble y cumple con su función

لا يركب باي طريقه تفكر فيها حاولت بكل الطرق مافيه تناسق بين الفتحات لتركيب المسامير الافضل تشتري ستاند عامودي يوضع بدايت الكرت هذا ابعد عنه

El producto funciona a medias, permite compensar un poco el estres de la tarjeta grafica, termina sediendo al peso de la misma. Como soporte cumple a medias. Muchos se quejan del RGB pero en lo personal eso no tiene importancia para la función que debe desempeñar y es el de dar soporte a la tarjeta de video.