Garage Work Bench with Pegboard - Metal and Wooden Workbenches - Suitable for Most Garage Equipment - Workbench Containing - Storage Drawer, Shelf and 20 Hooks - 230kg Capacity

Really impressed with the value and end result after assembly, it did take a couple of hours to put together, but I was able to do it myself with a hammer, spanner and screwdriver. The assembly instructions are ok and are quite through, although you do need to pay attention, I did put in a section the wrong way around, but it was easy to pop-out the pieces to correct and re-attach. And once all the wood panels are in the entire bench is really solid. My only complaint is the peg board hooks are really easy toknock off as they are cantilever (L-Shaped) and I am always picking them up, but I expect I could change these easily enough.

I ordered the bench on a Friday with an estimated delivery of the following Wednesday to Saturday but it came on the Tuesday, seeing as Evri delivered, a pleasant surprise. Not the most sturdy of benches but adequate for my needs, if your looking for one to hold a car engine whilst working on it, not for you. After unpacking all seemed ok, but when we tried putting it together found issue with the parts as well as how the were itemised, alphabetically. The instructions are not very clear but able to be followed carefully and slowly. On other reviews, the flimsiness of the parts was mentioned as was the length of the bolts. Yes, it is quite flimsy, but once put together isn't to bad. As for the bolts, luckily I had a few longer ones as i needed 4. The biggest issue was, what turned out the be the draw runner holders. They were wrongly labelled and both righthanded. I contacted the seller and they replied straight away but the solution was not to replace the parts easily but to send me a new package, take out the part(s) needed and then arrange for the remaining package to be returned to them, at no cost to me. This would have took up a week of waiting for delivery and returning, and would the part needed been in. It was easy for me to drill the two holes required, all finished in 30 minutes. I've given this 4 stars; 3 for the bench - instructions, build and missing parts, but it's 5 stars for the customer service and the discount. Would I recommend this bench? Yes, if you've got the patience and the right parts.

Looked at this for a while before deciding to purchase. Read the reviews, did my research. I knew that it was going to be an experience to assemble based on all the previous reviews - however nothing prepared me for what I experienced when it arrived. Open the box, everything well packaged and labelled, take everything out and separate everything (a previous review recommended this). No instructions. NONE. I was expecting bad instructions, but there were NONE at all. I double checked the box, and every part in case they had become stuck or wedged between some parts, but no, no instructions. I went to the manufacturers website to check if there was a PDF version available, no, however there was an assembly video, which was terrible but did allow me to work out the order things needed to go together, but not which parts to use or anything. Luckily I am pretty well minded when it comes to putting things together, so after some trial and error and looking at the listing images and the video, I managed to get it put together - after almost four hours! As is said in one of the reviews, with the main frame, there is one of two ways the back supports go together, you've got a 50/50 chance of getting it right, fortunately its not overly complicated to retrace your steps to switch them around. My last point is the screw lengths, there are three different sizes, two look very similar, but one is shorter than the other, make sure you use the shorter ones in the right places so you still have longer ones when you need them (I assume the instructions would tell you this). I would honestly give this a four or five stars, because once its assembled, its pretty great. It's sturdy, well made, looks good, and it's great value for money. It's not going to cut it if you are doing anything aggressive. But for light work (I use it for bicycle wheel building, and bike maintenance) I works brilliantly. However, the fact that there were no instructions and the experience of putting it together was quite frankly terrible, I can only give it one star. Do not buy if you have no patience, or an inability to put things together. If you have an eye for constructing things, you should be fine.

This workbench is so close to being fantastic but is let down by a few key things. 1 assembly is fiddly and is not helped by many mistakes in instructions. Holes not lining up (see pic) so needing to be drilled out. Instructions seem wrong ie steps out of order so when it comes to fit shelf wood and bench top you have to take bolts back out to fit them. And lastly the draw is held on by the smallest screws and the bars the rollers screw too have to be installed upsidedown to allow clearance. And last thing I was missing 1 screw and bolt (luckily I found one to fit from my nut and bolt pot) but if you don't have that luxury then draw wouldn't be able to be fitted. Having said all that once assembled it's actually very good, decent size, very sturdy and a nice size pegboard. Yes it's cheap and the end product is worth it but dam it's the worst flat pack ever due to the instruction mistakes and missing bolts.

In the past I have purchased a number of VonHaus products and have always found them to be well designed and well made. This work bench is no exception. It is fairly easy to put together. I thought I had parts missing and contacted customer service who were very helpful, I then found the parts in the packing. When completed the bench is solid and stable, overall an excellent product.