Inkbird All-Purpose Digital Temperature Controller Fahrenheit &Centigrade Thermostat w Sensor 2 Relays (ITC-1000)

I was almost put off by the negative reviews, but I got this thermostat for my leopard gecko egg incubator. I needed something that would keep the temp at 88* F constantly. Although this T-stat was a little difficult to wire in initially, and required some parts it didn't come with (a plug, outlet, jumper wire), which is a small price to pay for such an inexpensive thermostat, it did it's job very, VERY well. I already have hatched healthy leopard geckos from two clutches, and I have another clutch that should hatch in about 3 days. The eggs are very healthy and this will be my first 100% hatch rate EVER. I also hatched cricket eggs in the incubator controlled by this T-stat. The T-stat has kept the temperature within 1.5* F in both directions constantly for several months now. I have been EXTREMELY happy with this product, so uch so that I ended up getting another one specifically for my cricket eggs. Same great results. Another great thing with this T-stat is that it's small size and convenient shape makes it very easy to build into whatever you are using it for, in my case an incubator. The only reason I don't recommend this for everyone who needs a T-stat is that wiring is a bit difficult. It requires at least some prior knowledge of electronics, and it's definately not "plug 'n' play". I definately wouldn't recommend anyone who doesn't have experience with electronics try to use this. You are dealing with 120v AC. Show some respect! But after it's wired in it works well. There are also two diagrams on how to wire it in, which are both feasible but it is a bit confusing. I recommend that you follow the colored diagram on the FAQs sheet included with the product, because with that diagram all the "hot" wiring is inside the unit. That will reduce the risk of shock, fire, etc. The yellow, ground wire on that diagram is unnecessary, though it is safer. Overall, it's a great thermostat for a great price. I will definately be using it again!

Picked up a mid-2000s Red Bull countertop mini fridge. It worked and cooled, but would occasionally "chatter" the compressor on and off, causing it to stall and trip the overload switch. After checking the overload and motor starter, the cuplrit seemed to be it's electronic thermostat circuit board. Parts are unobtanium, so ultimately just tossed it and replaced it with the Inkbird. Wiring it in was a snap, just follow the diagram provided. It's fans are tied to the compressor (cool) power. The "heat" side was not used as this was for a fridge. The only slightly tricky part was the original temp sensor had a very different resistance than the one with the inkbird, however, the wiring for it was sealed into the unit via the foam insulation and couldn't really be removed- or a new one shoved through- without drilling a new hole through the insulation and steel case, which I wanted to avoid. I ultimately clipped off the wiring at the probe and the controller, spliced the Inkbird probe onto the wiring, slid it back into the original probe holder, and then attached that wire into the Inkbird. Reusing the original wiring through the case, but with the new probe at the end. Temp was reading correct. At that point, it was just a little trial and error playing with the set point and temp differential. For a drinks (well, mostly beer) fridge, this is what I found worked the best for ice cold beverages, without it excessively cycling on/off. Set point- 32* F Differential- 12* F (so, it will kick ON at 44*, and OFF at 32*). I've found at room temperature, this results is a roughly 30% duty cycle on the compressor- it runs for about 10 minutes, then is off for about 20). I've had no issues with even soft drinks freezing or being slushy- popping a can fresh out of the fridge and checking the liquid temp shows about 36*- or the "average" temp in the box. I left the compressor lockout at the default 3 minutes (the cycle time is much longer than that anyway, so it really should never be needed), and the temp "calibration" also at the default (zero), as I found it's reading to be spot on. For a fridge with fresh foods I'd probably keep the differential a bit lower for safety, but for canned beverages, a bit more fluctuation is fine. Saves power and wear/tear on the compressor with less frequent starts. It's been running for a couple months now with zero issue. The fridge pulls about 120 watts when it's running- or only about 1 amp, so the 10 amp rated relays in the Inkbird are more than sufficient, no additional relays or anything needed. That's quite a bit given it's size, only a little less than a full size residential fridge/freezer, but these little commercial drink fridges have relatively high cooling power (to recover/chill warm restock cans quickly from constantly being opened- this was originally intended to live on the counter of a gas station). Anyway for $20 it's a no brainer. Got a fridge/freezer with a bad controller? Or just want to be able to customize the set points? Get this.

I love these, and have bought for several purposes. The included K type thermocouple is accurate enough to measure to .1 degrees resolution. From the few times I've used these, they are very close to actual temperature (+/- 1 degree), and do offer a temperature "shift" in case you do need to make an adjustment. I've used this to replace a mechanical thermostat on a 1930's westinghouse refrigerator, and it works great. I've also used this to build a chicken incubator. Again, it works great. it has an internal relay that handles quite a bit, and you can always run it through a "solid state relay" to power anything you need to. If you are using this for a refrigerator rebuild, I highly recommend you also buy the compressor starter capacitors also sold here on Amazon. I'm happy to have such value in such a cheap package. In reality, you can also use this for a sous vide controller. The only downside is that though the resolution is to .1 degree F, the control range is a minimum of 1 degree. If you wanted to hold exactly at 100 degrees, for example, it would kick on the heater at 99 degrees, and stop at 100, then kick back on at 99 degrees. One degree is the minimum range you can set. If you need any more narrow control band, I suggest you get a PID controller. For the vast majority of applications however, this can't be beat. The range is adjustable (on/off) to whatever you wish, but not less than 1 degree. It is adjustable to display C or F. It also has a setting to prevent "short cycling"... that is, kicking on, and off your compressor so often that it burns up faster. The setting puts a timer on the minimum time from when it last went off, to when it goes on, and visa-versa. For example, you can set it to not to cycle less than 3 minutes (factory default). The probe cord is about 6 feet, and the probe itself is plastic coated and just over 1/2 inch. It seems pretty responsive (you hold it in you hand and it warms up about 1 degree F per second, or faster). I hope you find this review helpful.

I purchased the ITC-1000F digital temperature controller to replace a failed mechanical controller in a wine cooler. Doing the research, I read many reviews, especially the one and two stars. I was concerned that this might not be a long term solution but at the price point, it was worth the risk. Thanks to Amazon Prime, I received the device a day earlier than expected. It was packaged well and appeared to be well constructed for such a low price. The part I was replacing cost about $150.00 and this cooler has has had three of these in the last ten years! The instructions that came with the unit were poorly written. In fact, there was a supplement that showed a different wiring diagram than what is printed on the unit. Before installing the unit into the cooler, I wired it temporarily to make sure that it worked correctly. The mechanical thermostat had two wires as it was a switch. I found the line wire and the load wire. These were connected to terminals one and two with jumper wires to 7 and 8, which were for the cooling mode. The temporary connections turned on because the temperature was much higher than the set temperature; cooled the cooler down ;and then shut off the compressor when it reached the set point. SUCCESS! After this, I cut a hole into the cooler grill to mount the unit and wired it for the permanent installation. By the time I completed this, the temperature was several degrees above the set point. I turned the unit but the compressor never started. FAILURE! I contacted Ink-Bird at the "support" and "cs" email addresses and gave them detailed information on the installation and the failure. Even though the website states they would try to respond in 24 hours, I did not hear back until the third day and they only sent me a wiring diagram while ignoring my questions. By then, I diagnosed that the switch on the 7&8 terminals was not working. THANK YOU AMAZON! I contacted Amazon, explained the problem and they had a replacement unit to me in one day! I wired the new unit temporarily and it worked immediately. This time I left it this way until the unit had cycled several times until the next morning. I installed it permanently and it has run perfectly for four days. SUCCESS! The temperature controls are accurate and needed no calibration. The settings are precise and the differential settings keep the compressor from being overworked. If the unit lasts, I will be really pleased.

Sheesh. Whatever passes for Madison Ave in China got a hold on the manual for this. Pseudo engineering Jaberwocky for what is a robust simple device. This performs two functions, closes a relay designated cooling if temperature rises above setpoint + "differential"; for which you may read " the highest temperature excursion above where I want it to be". The other function designated heating works the same way but opposite:" lowest temperature excursion below where I want it to be." The cooling function also features a programable delay before that relay closes if you so desire. Why all this and not just on and off ? Well, its clearly designed for HVAC compressors. Read fridge, freezer, air conditioner. Which in the real world all just blow cold air at one temperature. So when you set your room Tstat for 73, you do not get air blowing out at 73, but lower. After awhile the temp drops to below 73 and the beast shuts down.; Then things warm up above 73 and the cycle starts again. So the room temp "desired" at 73 actually ranges a couple of degrees above and below your setpoint. On the Ibird you choose setpoint and reasonable excursion. For a fridge this might be 34, ie above freezing and a differential of 6 ie: no higher than "unsafe for food zone" above 40. This is exactly how the cold control in fridge works. You could set the Ibird for 34, no differential, but your compressor would basically run all the time. Now, pop the door root around for a beer, warm air rushes in hits the thermistor sensor and the compressor wants to start again, fair enough, but the actual temp of the whole fridge compartment did not really rise much. So a compressor delay of a few minutes saves some bucks. Actually a lot of bucks if people keep going in and out ( of fridge or house) because now the compressor wants to cycle frequently, which is bad because there is a minimum off time the manufacturer specs before power should be applied. Ignore it and pay for a new compressor. Pro: works well, easy to program. Con: the usual low current screw down connectors, ok for 110 volt in and thermistor, no way to get 10 amps in and out of the relays. FWIW, I pulled cover, relays actually say 15 Amps @ 115. Do not believe it. Add an outboard relay capable of providing full inrush current rating of your compressor and use those built in relays and the wimp connector to trigger the outboard relays. Got mine for $0.99 at electronic goldmine.

Keeps my glycol chiller at the temp I need it at without short cycling. An excellent product at an affordable price.

This is an amazing little controller for the price ($15! No way!) and for a simple dry contact calling for heat and one dry contact to call for cooling. Claims to have a 10A rated contact at 220 VAC. Pretty impressive, if true! I only use the “call for cooling” (close a contact) to turn on a radon reduction system fan with an inrush of 0.7A and 0.5A running current at 110 VAC for when the attic is above freezing. (When the warm, moist air from the sump pit hits the cold attic PVC pipe it generates a LOT of water. Gallons! I built a condensation trap - inverted P-trap - and the water drains back to the PVC ahead of the electric fan to protect it, but I do not want the water to freeze solid and plug the drain tube.) I was doing the on/off switching manually... monitoring the temp and flipping the breaker off and on. The Ink Bird automates this. Sensor cable could be a bit longer, but it reaches just fine because I planned it to be mounted as high on the wall as possible. The Budd box I stuck it in is nice, too, but 2x the price of the controller! LOL Still a good deal. The manual is a little confusing and I can see why some report the wiring diagram is incorrect, but it is not; at least not the one that I got. It is crudely drawn, but it was correct. I played with it on the bench and made some notes so that I made sure I understood which contacts I wanted to use and how to program it properly... using a hair dryer to warm and cool sensor for triggering the relays and an ohm meter to monitor contacts. You can offset the temperature display a few degrees to calibrate it to a known temperature. My garage attic is the same temperature before sunup as outside temp and I made it agree with local weather which matches my car temp and the Ink Bird and another remote thermometer I was using to switch manually. It’s been in operation for a couple months with no hiccups. I check to make sure it isn’t “getting hot” or anything, too. I admit I was skeptical and had low expectations but have high praise now... if it keeps working for a few years even, I’ll be happy. Received it quickly and in protective packaging with everything needed... except the Budd enclosure, of course.

OK, so I am a total novice here but I can say this was an easy swap. My Carel Controller (Code PYFETZN059 / Model PZFES0P111K) got water logged and eventually fried. It stopped keeping temp for my Argus Cooler. I looked for a replacement and the part was discontinued. The suggested replacement was $120-$300 by Carel and the cooler company wanted $200 to put it in. So I found the Inkbird controller on Amazon and decided to take my chances. I just followed the wiring diagram from the Carel controller and matched it up to the Inkbird. The Inkbird fired right up and was easy to flip into Farenheight mode, and set between 32-38 degrees. The cooler has no heating element so I didn't have to worry about those wires. It has been holding temp, and does exactly what it is supposed to do. Also what is cool is that they include a shield for controllers that may be mounted at the bottom of coolers and get water on them. I taped it up a little extra in case water leaks onto it. I added some photos in case anyone wants to see what I did. All in all I am very pleased with this controller, and I am extremely happy that I figured it out on my own and didn't have to pay a company to do it. I tried to use as much as I know about my situation here for anyone who might be Googling how to replace these things. Good luck.

Excelente producto, los materiales de muy buena calidad, funciona muy bien para control automático de ventiladores para mi acuario.

Great replacement/upgrade for traditional mechanical fridge thermostat. The mechanical thermostat on my fridge failed. Original piece was no longer available at a reasonable price, so I got a universal replacement. It seemed to work, but had a terrible hysteresis....meaning it would run the compressor until the fridge was cooled to the desired 2 degrees C, but would only turn the compressor back ON again when the fridge temperature rose to a balmy 8 or 9 degrees C. I found this wide margin between compressor OFF and ON temperatures to be unacceptable. I stumbled upon this Inkbird ITC-1000 unit by accident and was skeptical at first but decided to give it a try. VERY VERY pleasantly surprised !!! It is compact, and once you understand the programming functions and parameters it is very easy to use. I had to read the instructions a couple of times but after that it was a breeze. Wiring the unit is simple. Power cord, sensor, and in my case, 2 wires to the compressor control wires. I tested the compressor running current and it's about 2 amps.....the ITC-1000 relay contacts have a spec of 10 amps, so no problem there. The unit has been running without issues for a few weeks now. I have set the temperature ("ts" in the programming menu) to 2 degrees C , and the delta ("ds" in the programming menu) to 2 degrees C. So, the compressor will run until the fridge cools to 2 degrees C, then switches OFF. It switches ON again when the temperature rises to 4 degrees C, which is "ts" plus "ds", and starts to cool again. Overall this is an excellent unit and is cost effective as well. HIGHLY RECOMMENDED.

Esta bien y los diagramas te ayudan a la instalación solo que la configuración es un poco complicada.

Remarkable product for the price. Easy to use and install. We have a Sub-Zero Wine Cooler. The analog thermostat is no longer available from Sub-Zero or the thermostat manufacturer. I bought this controller, tested it and it worked perfectly. It’s actually a tremendous upgrade. Now I can control the temperature to within 1° and I can see what the temperature is at any time. Before I just had a rotating knob analog thermostat that failed every few years. Note that I had to cut the steel mounting bracket and front cover to install this digital thermostat. It needs AC power which can be either run separately or spliced in from line in to fridge. Another great feature is that you can set a temperature delta and a compressor delay. Temperature delta means that if you set a delta of 3° for example, and set target to 50°F it won’t turn on until it hits 53°. A compressor delay means that you can set a delay so that the compressor doesn’t burn out by cycling on and off too quickly. Both settings will reduce energy and extend life of compressor potentially.

Works as advertised, love the adjustable temperature sensitivity!