Tatcical Flashlight & Scope Optics Ring Sight Mount Set, Barrel Clamp Mount with Standard Rail for 10~12 Gauge/13~15Gauge

I guess I am the first to give this mount a try. I needed a way to mount a light and laser to my wife's Remington 870 Express 20 gauge with rib. I first tried a saddle mount, but they are all a bit clunky, and not at all an elegant solution. I looked at the Beamshot RF9 Mount, and this NcDe unit and couldn't be more satisfied with choosing the NicDe unit. Unlike the Beamshot, this unit needs no shims, although both units fit a wide range of barrels with or without ribs. The description also specified the dimensions and range of fit very precisely, Fits perfectly and snugly without using any shims on her 20 gauge. A perfect solution to mounting a picitinny on the underside of a ribbed shotgun barrel. I am not saying the Beamshot wouldn't work as well, but I think this one is a little better unit. Aluminum, well finished, nice and solid with no shim wiggle. Highly recommend.

This rail mount was exactly what I was expecting. I quality, light but strong and well built piece. I wanted a small tactical flash light/laser combo that was decent for my 20 gauge Stevens 320 Security. Wanted it to look clean, fit right and stay on. It’s perfect! I know some have complained that screws aren’t big enough for a 12 gauge but, I was careful to open them up evenly and even had room for some protective tape so as to not damage magazine. I believe this could fit a 12 gauge mag cylinder if you’re careful and know what you’re doing without the need to go to a hardware store for longer screws. Either way, it’s worth the trip if you have a 12ga. It’s fits great and standard picatinny gear fits snug and perfect. Again, I wanted something that installed clean and custom. This did it!

🙂

Difficult to find forend accessory mounts that will fit my Mossberg 590A1 since the barrel is attached to the forend with a mount that is glued, preventing slip on accessory mounts. This one does separate completely into two pieces, fitting easily and snugly. Works fantastic with my Streamlight: Streamlight 69260 TLR-1 HL... https://www.amazon.com/dp/B00B8Q31UQ?ref=ppx_pop_mob_ap_share What a sweet setup! I just wish this mount was Parkerized rather than regular black anodized, but it's the best I could find after much searching.

I INSTALLED THIS ON A REM 870 .12 GA/SPECIAL PURPOSE HAS A 21" RIBBED BARREL. IT DOES FIT REAL TIGHT AND SEEMS TO BE REALLY SOLID, HOW EVER I HAVENT SHOT THE GUN YET SEVERAL TIMES TO SEE IF IT MOVES OR FALLS OFF. FROM WHAT I CAN SEE SO FAR THIS IS A REALLY TOUGH WELL MADE MOUNT SO I DONT EX- PECT TO HAVE ANY PROBLEMS WITH IT.....YES I WOULD RECOMMEND.

I bought this to mount a Streamlight TLR-1 HPL flashlight to the magazine tube of a (Ruger made) Marlin 1895 45-70 Trapper. Fits absolutely perfectly and it seems like it should hold firm fine (haven't actually shot with it mounted yet however).

This product is made with solid quality. This worked great for attaching a picatinny rail to the barrel of my tactical shotgun. I then attached a flashlight to the rail and it worked perfectly. I think this is an excellent product if you want to add a picatinny rail to a long gun barrel.

Will not work on 12 Gauge Iver Johnson single shot unless you put it out where its not usable. this company does however have one that will work made for 7, 8 gauge , 1.6" wide

Unbelievable quality for price.....very happy

Pretty solid for something like a flashlight, be sure to use a thread locker or it will become loose in 2-5 shots

Easy to install and fits exactly as expected

Installed on tube magazine of A Mossberg 500 Persuader. Allows just enough room mounted carefully at the end of the tube to permit full travel of the action slide. Worked well, no complaints, not the most inexpensive method, but used in conjunction with “Weltool tactical offset flashlight mount” as needed flashlight to be parallel to barrel to avoid interference with sling.

great product built well fit nice no sharp edges very happy with every thing...