KRYDEX IPSC USPSA IDPA Competition Shooting Multi-Angle Adjustment Speed Shooter's Pistol Magazine Pouch Mag Holster Holder

I like the adaptability of these mag holders. Fits Evey magazine size and shape. Very sturdy and sound construction. They hold the magazine just right with adjustable tension , even great for upside down carry if you need too. I have purchased another set. If you have magazines and need them attached to your body or bag, then these do the job and then some.

I ordered one of these to pouches to test it out. Loved it so much I ordered 4 more. These pouches are identical to the Black Scorpion pouches. Exactly the same. The only difference is the Black Scorpion emblem. They are fully adjustable. They have a swivel tension mount so you can rotate them and cant them towards or away from your body. You can also raise or lower them on the belt mount. The only negative I have is that it takes a bit to get them mounted on the belt so they don't lend well to a rig where you're swapping or moving the pouches often. Other than that, they are a great value. One recommendation is to use Loctite on the threads once you get them to where you want so they don't loosen and move Mainly the main screw that holds the swivel mount.

They work good for the price, not top tier quality, but they perform as advertised.

These great as long as you're using them with the right size belt. After realizing I needed a belt no more than 1.5, I bought the right size of they are perfect. Basically just slides onto the belt with just the right amount of tension to hold firm once the belt is tighten down.

I just had the mag carriers delivered today to set up my belt ahead of a test and tune on Saturday. I'm using a Shooter's Connection Ultimate Competition belt for those who know. Let's start with fitting the carriers to the belt. They don't slide over the belt at all. The included paperwork suggests loosening two screws on the back of mag carrier's slide. Loosening two or even all four is not enough. I had to completely remove all four screws and then press the two halves back together while tightening the screws down. These carriers are not moving at all any time soon. Someone else who bought these had 3D printed a new back piece that works with thicker belts. If you're out there I need that STL file. Next is adjusting the cant of the carriers. That requires removing two small lock nuts and a plastic cover plate on the front of the carrier. IF the threaded studs holding that plate to the carrier frame fall out good luck getting them back in without tweezers or something. Such a pain but once you have the cover off you have to adjust the T30 screw through the opening in the mag carrier. Best to do this while it's on your belt so you can get a feel for it because like I said your not moving them laterally once they're on the belt. Last I think is swapping the carriers from left hand side of your belt to right hand side for other handed shooters. I shoot left handed and tried to follow the paperwork on how to switch the carriers from left handed to right hand and it made no sense so I just stuck the carriers on my belt as is. I may be using them backwards but you couldn't prove it by me. The mags fit just fine. Now that they're all mounted and never leaving the belt unless there is some sort of catastrophic failure I can say that the construction and material quality is pretty good. They look every bit as good as the product pictures online. I even dropped one or two on the floor accidentally and there was no breakage so that's good. I don't expect any problems when I actually run these in a few days and if all goes well I'll update my review. If it doesn't I'll update my review. These would definitely be better rated if they fit my belt without all the hassle or the desire for the 3D printer file that someone else made. Edit: Ran these through several 3-gun stages on Saturday. Overall they worked well except one of the carriers rotated itself loose and almost came off its mount. Fortunately I was able to rotate it clockwise about a dozen times and it tightened itself back down. I'll keep running these this spring/summer and I don't think I'll have a problem.

Great.

I haven’t run them in a match yet, but they appear to be quite sturdy and easy to convert from a double stack to a single stack (to run with my 1911). These are very impressive for the price and I was just practicing dry reloads and was very happy. I would say worth every single penny. They were challenging to get into my belt, so now that they are on, they are staying on. So if you are someone who likes to swap around setups, I wouldn’t recommend these or I would recommend getting a second belt (that’s what I did). I do have two minor complaints, but again for the price, I can live with both of these: 1. I wish these came with instructions of some sort on swapping out the spacers and how many of the rubber washers you should leave in so that it makes your adjustments a little easier (again a very MINOR thing) 2. I wish the panel on the front that allows you to access the screw that adjusts cant of the mag was easier to get off (again, A very minor thing).

I saw these and thought they would be useable for my backup competition gun. Looked like a great price point. I was very, VERY disappointed. Whoever designed this put no thought into how the end user would need to adjust the magazines. The screws are on the inside for reasons I can't comprehend, and cannot be flipped around, so rather than easily taking the plate off, lining up your belt, then screwing back on, it is impossible without manipulation of the magazine holder itself, WHICH by doing so you loosen the magazine holder so you magazine flops around will no longer stay up right. Fortunately, they have adjust to fix that.... BUT the screw to adjust it is INSIDE the plastic pouch, so you are unable to reach it, to tighten the magazine pouch you just had to loosen to install it on your belt. Seems absurd? Because it is. I'm shocked so many people use these. Get some DAA Racers for slightly more money and save yourself the hassle. Buy once, cry once. Lesson learned.

These work awesome. I’m no competition shooter but I’ve ran my mags through them a ton and they have held up perfectly. They showed up exactly as they were advertised. Fast shipping as well!

They work well with Glock mags

These mag holders are affordable knock-offs of high end, competition-oriented holders which can cost 3x+ more per unit. If you are patient and handy with small tools, they can provide a low cost entry into competitive practical shooting sports. They are highly adjustable to a range of magazines and fit most common belt systems (up to 1 1/2” width). Made of plastic, they will not have the lifespan of high end units made of aluminum etc., but until you get into high frequency, intense practice and competition sessions they do the job. You have to spend time adjusting them to fit your mags, dealing with many tiny nuts and screws as others have mentioned (would be nice if company included some spares as they do tend to go walkabout!). Getting them mounted on your belt is also a bit of a pain; once you get them setup you will want to leave them on. As shown in accompanying pictures, I made a couple of mods which improved holders a bit. As they come, mag retention is by friction alone, which changes with use, temperature, etc. You can tighten the top black knobbed bolt down for secure retention, but then mags may be sticky to pull out. I epoxied 3/4” by 1/8” thick rare earth magnets to the inside center of the outer panel of each holder, so the magnet was centered over the fortuitously positioned hole through the inner panel of each holder (silver disc visible in photo). The resulting clearance is perfect for effective mag retention, without any scraping or interference and allows one to reduce the friction screw pressure, giving a secure but slick action. Note some competitions disallow magnet-only holders; it’s not clear if they would rule this system out, but if that ever was an issue one can quickly undue 2 nuts and remove the outer panels with attached magnets and use friction retention alone. Also as seen in photos, I drilled a tiny pair of holes in lower rear corners of each side of holders, and pushed through a 4-40x1” screw, with a piece of black plastic tubing as a spacer (cut to fit my mag thickness), with a nyloc nut on inner end. This addition made the mag holders much more sturdy and stable. Finally, as others have suggested, once I had all the holders adjusted so mags fit well, and got them mounted on the belt at the correct angles (tilting slightly away from belt, and slightly forward works), I applied blue medium threadlock to every nut and bolt (except top friction knob) and retightened everything carefully. Several friends use these holders as well, without modification, and seem happy. They use the holders with Krydex belts which also seem fine. I had a similar but higher-end Black Scorpion belt, on which these customized holders also work well.

Seems well built. Easy to switch to lefty holds glock and smith&wesson mags supper tight but are easy to pull out and put back so There great for speed loading but these are my first mag holders like this so i have no other brands to compare too. I will repost. If they break

Received this 2 days ago, and they are great. Packaging was great. Only thing that I question is that to adjust the angle and/or tightness of mag holder you need an Allen key which was not included. I didn't take off a star because almost everyone has allen keys. These mag holders are a welcome addition to my range days.