Aeroponic Cloner Machine, Cloning Machine 35 Site for Cutting Rooting Germination Kit Using 1.625 inch Neoprene Clone Inserts

pair this with a timer that can turn on and off every 15-20 minutes to cut back on undue heat that comes from the pump always running, very good machine 100% success rate thus far, root buds developed within 72 hours full roots after 7 days

Simple, effective, decent quality. I used this in conjunction with Southern AG Garden Friendly Fungicide, Protekt, and some Cal-Mag and had roots forming in just a few days on some cuttings (others took upwards of 3 weeks before I saw any roots). You do not need to use the humidity dome for this style of cloner. In fact, I think putting the dome over this while the pump is going might lead to too much humidity for some plants. No timer for the pump required, if you can keep temps in check. Pro tip: Keep the water temp in the cloner between 70-80F. You can run past 80F, but once roots start showing I would lower it to below 80F. For my climate this meant putting a heat mat under the reservoir on an on/off thermostat. 10/10 would buy again

a little too early to know if it’s doing good with my plants that I am cloning, but I think it’s gonna really be nice in a few weeks seeing roots growing out of the bottom. I gave four stars because the discs that holds the stem of the plants , won’t stay in their hole. The hole is either too small or the discs are a little bit too big that I have to keep pushing them back down. THIS IS NOW ONE STAR I’m sorry and sad to say I have to return. #1 It leaks really badly. #2 The pads won’t stay in place. Any movement and the plant steam will fall over to the side and water shoots out. #3 The pads are too small to hold a medium size steam. You are very limited to what you can place in the hole of the pads to propagate. #4 This is not worth the money for the trouble and probems. I'm going back to my homemade one. I hope the company will see this and make MAJOR adjustments. AND lower the price!

I wish there was a way to extend the Humidity dome to 2 foot high.. as I clone plants that take well to cuttings. A humidity dome of the same that sits itself on the outside of the cloner box.. This allows you to clone fully leafed and flowering cuttings (for compatible plants) and make it really fast for the plant to fruit quickly - Example PEPINO FRuit. I replaced the 120 volt pump with a local pump and it works very well. A 230 Volt option would be very good for sale I wish the cloning female sockets could have been a little bit deeper so that it can hold longer cuttings better. The plastic material for the cloning machine could have been a little bit thicker for more safety.. In Asia temperatures are as high as 34 C and cloners put these in their bedroom or in a grow tent in a very cool place and it would not be nice if the bottom was to spring a leak. Making the plastic thicker would allow me to add a small auto top up valve. I use 2 of the cloning sockets one for Airpump and one for Occasional OZONE to clear out any decay issues. I use a cycle timer to run the pump for 15 mins and after ward a 6 min + rest to prevent the pump from heating up and to allow the roots to have some "air time"

This cloner is absolute garbage. It will work great for 1 run, then you will have issues. The neoprene collars are cheap and close all the way, causing the misters to spray through the cracks and sit on top of the collars, in high humidity, which causes pythium. I’m going with the turbokloner

This is my first aeroponic setup. tried doing a small pineapple guava grow, but the guava is a bit hardy and didn’t take. Switched to dragon fruit and it’s working great. The slots are small so I had to cut the foam plug to fit the dragon fruit cuttings. The dome isn't hard plastic, so bending the wire supports is needed for a proper fit. Kinda tighten the corner bends a little. The sprayers reach every site with plenty of water. Be careful that the slots are facing inward, this is to keep the water from splashing outward, if it does at all. The little pump is a work horse!! The length of the cord is perfect, not short at all. Checking water levels can be a chore depending on what you have rooting. For the convenience and size, definitely worth it!

The pucks fit a little loose In the pockets of the cloner. which allows the starts that are really thin stemmed to fall through the hole.

did not experience issues with roots being blasted off. if YOU do, try usin the perimeter plugs. there's a 12" light, with stand, that works great. cover seems like raincoat plastic, but will support that 12"er... ;D . could use a less messy access panel, or- one could just turn it off. I'm just not smart enough to do so. i had to revisit this! i get 100% clone rate. 4-6" roots, in 10-12 days. no problems with the cover. if u cheat, expose roots to natural light and check, by lifting- u might weigh down collars, with extra collars. that also helps prevent leakage, from loose collars. one might also duct tape the extra electrical holes... no leaks, then, only overspray, from peakin. use green light, if u expose roots... i go 24/24 & have no problems. i use clonex gel, a lil saliva, dash of cinnamon and a big -oops-drip, of pure, natural, honey. if i had willow water... i wouldn't need it. it's about inoculation... bout 200-300ppm of clonex solution in tank and ph, b/t 5.7-6.0.

Pump stopped working after 10min waist of money

Pump hat nicht funktioniert und das Produkt ist sehr minderwertig verarbeitet für den Preis.